I upgraded the BIOS of my S1200V3RPM (XEON E3 1265L V3) to 3.03.0006
To do this, I insterted a USB stick with the new BIOS, booted to the internal EFI shell and then the BIOS upgrade started by itself. It ran through to the end without any issues.
I then power cycled the machine to reboot and now it does not boot anymore. No beep, so POST screen, nothing.
How can I get back to a working machine?
Проблемы с запуском материнской платы Intel Server Board S1200V3RP. Конфигурация ПК: 1) Minitower Chieftec LT-01B-OP. 2) Intel core i3-4370 3.8 GHz. 3) Kingston HyperX в Fury <HX318C10FRK2/16> 4) Zalman 24+8pin 450W. Был выполнен первый запуск появилась информация материнской платы.
Был сбой питания.
И системный блок перестал включаться (черный экран). Сброс Bios не помог, вентиляторы работают, звуковых сигналов нет. Помогите пожалуйста с решением проблемы.
Hello. Motherboard intel s2600sw. Trying to install windows (server 2012 r2,10,8.1) , it hangs at the stage bootloader of the system.The installation of Windows 7 and Windows server 2008 R2 runs fine . Please help.
Hello!
I have problem with hyper-v. I try to install VM on Windows Server 2012 R2 or Windows 10 and the VM is "hung".
The OS is clear. OS on the server - Windows Server 2012 R2
System BIOS - R01.01.0018
ME Firmware - 03.01.03.032
BMC Firmware - 1.46.9995
FRUSDR - 1.13a
VTx is enabled and the server power off for correctly work.
Hello!
I have Intel R2312WTTYSR. I cannot downgrade bios version. I tried to downgrade via shell and ofu. And i used different version firmware (01.01.0014, 01.01.0015, 01.01.0016). The shell and ofu says "The capsule file in the update package is invalid".
Current version Bios 01.01.0018
Hi there,
I have a P4308CP4MHEN Intel Server System that I would like to put in a rack, do I need anything else than Enhanced Value RAIL AXXELVRAIL?
Best regards,
Klemmi
Hello!
I have Intel® Server Board S2600WTTR.
For UEFI mode, how to create bootable usb with Windows server 2012 R2 and what kind of settings i must do in BIOS?
I ssh into a s2600wt BMC and I want to turn on the system via SMASH-CLP console.
show system1/pwrmanagement1 returns the property of CurrentPowerState
set system1/pwrmanagement1 CurrentPowerStatus=ON returns
CurrentPowerStatus is read only
what is the set command to turn on the system?
Hello from Brussels,
We will switch from a failed S2600CP to a new S2600CP that will (hopefully) be received this Monday.
Is it a procedure to transfer the RAID1 containers without loosing all the data and operating system ?
Thanks in advance
Regards
Tony
I have a S5520HC system with dual E5520 Xeons and I want to upgrade the memory to 64GB.
I have 8x 8GB RAM sticks, will they work in that configuration?
Hello,
I have a problem in my S2600CP2J board, firstly I installed a GPU (MSI GTX 760 OC) on the x8 blue PCIe slot the second one after the x16 slot, when monitor connected with the new GPU, the screen not show anything during boot (no POST or windows boots screen and no signal to monitor) and the monitor turns on after windows enter to the login page.
After reviewing the BMC log I see some errors related with PCIe, the picture is attached below
Hi!
RAID-controller (9271-8i) connected to a backplane using two cables "SFF-8087 to SFF-8643". Should I remove HSBP I2C cable from MB to backplane??? As I understand it, this cable is only for the integrated controller on the system board?
Hi.
I have a SRCSATAWB on S5000VSA. After shutdown, and powering on controller (SRCSATAWB) didn't initialize, not in bios (loading process), not in windows.
It immediately, after powering on, beeping and flashing (amber led on controller) - 4 times, pause, 4 times, and no end of.
What can I do, and what happened?
How do I update SAS drive firmware when the drives are attached to a RS2BL040? I don't see this capability in RWC2 or the RAID BIOS. I have 4 Seagate drives, but one is down 1 firmware revision level, so I want to update it. SeaTools for Windows won't see the drives through the RAID controller, so I'm kind of stuck. Any help please?
Thanks.
Serial port is enabled in BIOS.
The same device with the same cable successfully connected to another motherboad (asus z97-a), so device problem is excluded. Tried Win2012,Win2008R2,Win8.1
Should I change something else on this motherboard to make it work with UPS by serial port?
I have a server system (S1200V3RP with E3-1200V3), I try to install windows server 2016 to upgrade the server, but can't find the driver for embedded raid driver, so I can go on for further installation.
HI there ,
a year ago i brought s1200rp motherboard for e3 1246 v3 processor which has processor graphics (p4600). but, motherboard i brought does not support it.
[1]--- i need to know which motherboard supports processor graphics (e3 1246 v3). and
[2]--- i want to replace my existing board (s1200rp- works excellent since purchased) with graphics capable board with less money (cant spend much)
any suggestions appreciated.
Hi,
I have a problem with a S2600gz server.
I can't access RAID options on boot. I don't see key combination to make.
I follow this article : Not Prompted to Enter the Intel® RAID BIOS Console During POST for...
But no way, I can't access RAID options, so I can't create RAID 1 to setup my storage.
Do you have any tip to help me ?
Thanks
Good day. I have a server R1304GZ4GC with 2 processors. If i want to extract one of them what will i have to do except extraction, of course. After i'd done this coolers started to fan with maximum speed. Do i need to change BIOS options, turn off some functions? Or maybe replace RAM?
Hi I have a problem with Barebone Intel R2208WTTYC1R I don't know what I doing for have to control of the FANS. When the SO (Windows, Xen, CentOS...) is installed, the FANs have a null workflow , because the temperature of graphics cards and heatsink CPU have a high temperature to the point of to burn. Please, Anybody could help me? Thank you. Kind regards.