I have a JBOD2312S2SP Intel Raid Enclosure (Intel® Storage Systems JBOD Family) at my house and woke up to screaming fan noises.  Warning light was blinking and the console showed this:

ID = 206

SEQUENCE NUMBER = 164362

TIME = 29-06-2013 03:13:39

LOCALIZED MESSAGE = Controller ID:  0   Power supply cable removed on enclosure:   1      Power Supply   1

Note I only have one power supply so if the cable was removed not sure how it was still running.  Right after that warning received the below messages copied from the logs so the top one is the latest:

ID = 243
SEQUENCE NUMBER = 164371
TIME = 29-06-2013 03:13:44
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       3

ID = 243
SEQUENCE NUMBER = 164370
TIME = 29-06-2013 03:13:44
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       2

ID = 243
SEQUENCE NUMBER = 164369
TIME = 29-06-2013 03:13:44
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       1

ID = 243
SEQUENCE NUMBER = 164368
TIME = 29-06-2013 03:13:42
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       3

ID = 243
SEQUENCE NUMBER = 164367
TIME = 29-06-2013 03:13:42
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       2

ID = 243
SEQUENCE NUMBER = 164366
TIME = 29-06-2013 03:13:42
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       1

ID = 243
SEQUENCE NUMBER = 164365
TIME = 29-06-2013 03:13:40
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       3

ID = 243
SEQUENCE NUMBER = 164364
TIME = 29-06-2013 03:13:40
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       2

ID = 243
SEQUENCE NUMBER = 164363
TIME = 29-06-2013 03:13:40
LOCALIZED MESSAGE = Controller ID:  0   Fan speed changed on enclosure:   1  Fan       1

Last message until 6 minutes later I powered up a computer to remove in and shutdown the system.  Pulled the power plug, put it back in, powered everything up, and it's running right now without issue.  Thoughts?

Edit:  As a side note, the Intel Raid Web Console shows this drive cage with 2 power supplies.  Always did.  I only have one.  So not sure if that's just how many it can hold or if it's just not intelligent enough to detect the number of drives.

Thanks.

Steve

I have a S5000PSL that had X5148's with big heat sinks and no fans.   The previous owner just jammed a fan on top of the fins of the heat sink.  I bought a pair of X5355 and now I'm really in need of better cooling.  There are still plenty of LGA775 coolers for sale but I can't tell if they'll be enough for this CPU, nor can I tell if I'll be able to mount two of them side-by-side as the CPU's sit fairly close to each other.

It looks like there was some kind of duct but the prior owner snapped off part of the plastic connectors and I'm not sure how to mount it or if it's even possible to use it.

Any suggestions?

Hi. I have a S1200BTL server motherboard  PBA E98681-304. I installed an E3-1240(v1) Xeon processor. I installed Kingston KVR13E9/8i(x4) memory. When I start the server, I get one long beep and the server starts to boot for about 25 seconds, shuts down and reboots over and over with no video. From all of the info I can find, this configuartion should work. PLEASE HELP!!!. Thanks.

     I had installed centos 6.4 to SR1550AL system with one CPU, but I got second CPU's fan today and tried to run server with two core but gives first green blink at status led and goes to power led to sleep(repeated too many times) then I had resetted CMOS after that status led amber on power led staying at green but no bios, what should I do?

we have a problem on installing Intel® Active System Console on a S5000vsa (platform product id SC5299brp)

The S5000VSA is discontinued.

We got the latest supported version ASC 4.4. the installation goes to about 80% and then stays stuck (left for over 1 day)

the on site tech said that if cancel is pressed the installation does not terminate until a proccess escript.exe(Intel\ASC\erlang\bin\)

is closed manually.

The OS is Windows server 2003 R2 (with all recent updates)

currently im waiting for a System Information Retrieval to get some more info from the system.

Also gonna try if the original cd's are on site to test the server provided version if installs without problem

(i saw that the cd version does some pre-installation checks)

I'm looking at picking up an Intel RS25SB008 (a.k.a. OEM LSI 9286CV-8e). I am wanting to add CacheCade to it, which I see is done via the AXXRPFKSSD2 feature key. My question's are:

• Will the resulting version be CacheCade Pro 2.0? I don't know that there ever was a CacheCade 1.0 version available on this board, but I want to make sure that's not what I'm getting.
• These has been quite a bit of chatter about a newer version of CacheCade coming (some suspecting 2.1 or 3.0) that, most significant to me, would raid the size of the CacheCade virtual drive to something larger the current limit of 512GB (1 or 2TB in the rumor mill). Given that I have nothing solid to work from here, I am not asking for "commitments" but would welcome well-educated guesses as to whether or not Intel will have a new key once this is available?
• The above wouldn't matter if you could use the LSI branded CacheCade key with this board, but given my recent experience with an IBM OEM of the LSI 9260-8i (IBM M5014), I am betting it's going to be something unique and not cross-compatible.
• While I realize the implications of doing so (voiding warranty, etc...) does any one have an experience with the RS25SB008 and trying to cross flash it to LSI firmwares?
• Last, and this confuses me the most... if you look at the specs on this card in various places, you will see it listed at PCI-e 3.0 and PCI-e 2.0. This intel page refers to it both ways on the same page! (Intel® RAID Controller RS25SB008) Very confusing...

Thank you in advance for any answers!

-Jim

I did like said at the manuel(it is shown by fotos down here) but I couldnt cleared CMOS to get to bios...

at the end gives me amber status led and blinking(green) power led. What should I do get the just bios ?

Hi,

this year we've sold throw NEC, a FlexPower based on Intel Modular Server v2.

It seems that Intel will stop producing Modular Server which are great chassis and nothing will replace them ?

Why ? Is this the new vision of Intel ?

Vincent

Hi all,

A week agoI bought anIntelmotherboardS5000PSL, I wanted to use it with2 IntelXeonE5440.

Thehardwareconfigurationis as follows.

Motherboard: Intel S5000PSL

Processor:IntelXeonE5440

Memoirs: HP 4 X 2GB2Rx4PC2-5300F-555-11-E0

Biosversion:8s5000.86B.07.00.0079

BiosPBA: D44771

Power:700W

When i turn on theserver,displayedthe following legend:

UnrecoverableErrorfound.System willnotbootuntilfatal error isresolved.

EnteringSETUP...

I could notgetbootfromany means, (PENDRIVE, CDROM, Hard Disk IDE or SATA, etc.) andI run out ofideas.

Ilooked at theErrorManagerbiosandcan see the following:

8180minor

19Afatal

8160best

8601minor

Please I needurgenta solution, either to upgradefirmwareorknow that I'mdoing wrong.

From alreadythank you very much

Alejandro.

I am planning to build up a SOHO server with a S1200BTS(R) mobo. As i don´t need much processing power a pentium CPU would be enough for me.

In the CPU compatibility list there are listed among others G840, G850 and G620. But afaik these CPUs do not include support for ECC RAM.

On the other hand the board manual mentions ECC RAM as stringently required.

How can one operate above mentioned processors in this board with the ECC-RAM without having ECC-support in the built-in memory-controller?

Best regards

Hi,

I'm looking into building a few storage servers, hopefully using Linux mdadm. I've been eyeing the Intel R2312GL4GS because of its physical disk carrying size. In the description it has varying RAID levels, but does not mention JBOD. Does that mean if I purchase this server im forced to use the build in RAID? Can I put the disks in some kind of JBOD setup?

Thanks

Greg

Installed latest BIOS, FRU, SDR & so on. Tried to change in BIOS - acousting section - no changes. Looked in sysinfo utility's log file - many strings about redundancy fan failure. But I have in this case only permanent fans with 4 wires instead of 6pinout. A part of log here:

System Information Retrieval Utility Version 12.0 Build 10

Copyright (c) 2013 Intel Corporation

-------------------------------------------

Platform Firmware Inventory

-------------------------------------------

BIOS Version....... SE5C600.86B.02.01.0002

BMC Firmware Version:

   Op Code....... 1.19.5018

   Boot Code.............. 01.17

ME Firmware Version:

   Boot Code: 02.01.07.231

SDR Version:

   SDR version: SDR Package 1.10

-------------------------------------------

Sensors

-------------------------------------------

LUN NAME        NUMBER    OWNER    UNITS        VALUE

------------------------------------------------------------------------------------------------------

0 Fan Redundancy            12    32    REDUNDANCY_LOST, NON_REDUNDANT_INSUFFICENT_RESOURCES   

0 SSB Therm Trip            13    32    STATE_DEASSERTED   

0 BMC FW Health            16    32    UNKNOWN   

0 System Airflow            17    32    CFM    150.000000   

0 BB EDGE Temp            32    32    Degrees Celsius    25.000000   

0 Front Panel Temp            33    32    Degrees Celsius    26.000000   

0 SSB Temp            34    32    Degrees Celsius    43.000000   

0 BB BMC Temp            35    32    Degrees Celsius    34.000000   

0 BB P2 VR Temp            36    32    Degrees Celsius    36.000000   

0 BB MEM VR Temp            37    32    Degrees Celsius    29.000000   

0 Pwr Unit Status            1    32    ALL_DEASSERTED   

0 LAN NIC Temp            47    32    Degrees Celsius    41.000000   

0 System Fan 1            48    32    RPM    READING_UNAVAILABLE   

0 System Fan 2            49    32    RPM    READING_UNAVAILABLE   

0 System Fan 3            50    32    RPM    READING_UNAVAILABLE   

0 System Fan 4            51    32    RPM    READING_UNAVAILABLE   

0 System Fan 5            52    32    RPM    READING_UNAVAILABLE   

0 Fan 1 Present            64    32    DEVICE_REMOVED/DEVICE_ABSENT   

0 Fan 2 Present            65    32    DEVICE_REMOVED/DEVICE_ABSENT   

0 Fan 3 Present            66    32    DEVICE_REMOVED/DEVICE_ABSENT   

0 Fan 4 Present            67    32    DEVICE_REMOVED/DEVICE_ABSENT   

0 IPMI Watchdog            3    32    OK   

0 Fan 5 Present            68    32    DEVICE_REMOVED/DEVICE_ABSENT   

0 P1 Status            112    32    PROCESSOR_PRESENCE_DETECTED   

0 P2 Status            113    32    PROCESSOR_PRESENCE_DETECTED   

0 P1 Therm Margin            116    32    Degrees Celsius    -48.000000   

0 P2 Therm Margin            117    32    Degrees Celsius    -48.000000   

0 P1 Therm Ctrl %            120    32    %     0.000000   

0 P2 Therm Ctrl %            121    32    %     0.000000   

0 P1 ERR2            124    32    STATE_DEASSERTED   

0 P2 ERR2            125    32    STATE_DEASSERTED   

0 CATERR            128    32    STATE_DEASSERTED   

0 Physical Scrty            4    32    GENERAL_CHASSIS_INTRUSION   

0 P1 MSID Mismatch            129    32    STATE_DEASSERTED   

0 CPU Missing            130    32    STATE_DEASSERTED   

0 P1 DTS Therm Mgn            131    32    Degrees Celsius    -49.000000   

0 P2 DTS Therm Mgn            132    32    Degrees Celsius    -48.000000   

0 P2 MSID Mismatch            135    32    STATE_DEASSERTED   

0 P1 VRD Hot            144    32    LIMIT_NOT_EXCEEDED   

0 P2 VRD Hot            145    32    LIMIT_NOT_EXCEEDED   

0 P1 MEM01 VRD Hot            148    32    LIMIT_NOT_EXCEEDED   

0 P1 MEM23 VRD Hot            149    32    LIMIT_NOT_EXCEEDED   

0 P2 MEM01 VRD Hot            150    32    LIMIT_NOT_EXCEEDED   

0 FP NMI Diag Int            5    32    OK   

0 P2 MEM23 VRD Hot            151    32    LIMIT_NOT_EXCEEDED   

0 DIMM Thrm Mrgn 1            176    32    Degrees Celsius    -58.000000   

0 DIMM Thrm Mrgn 2            177    32    Degrees Celsius    READING_UNAVAILABLE   

0 DIMM Thrm Mrgn 3            178    32    Degrees Celsius    -59.000000   

0 DIMM Thrm Mrgn 4            179    32    Degrees Celsius    READING_UNAVAILABLE   

0 Mem P1 Thrm Trip            192    32    OK   

0 Mem P2 Thrm Trip            193    32    OK   

0 Agg Thrm Mgn 1            200    32    Degrees Celsius    -24.000000   

0 Agg Thrm Mgn 2            201    32    Degrees Celsius    -24.000000   

0 Agg Thrm Mgn 3            202    32    Degrees Celsius    -23.000000   

0 SMI Timeout            6    32    STATE_DEASSERTED   

0 Agg Thrm Mgn 4            203    32    Degrees Celsius    -23.000000   

0 Agg Thrm Mgn 5            204    32    Degrees Celsius    -24.000000   

0 BB +12.0V            208    32    Volts    11.883000   

0 BB +5.0V            209    32    Volts    4.937100   

0 BB +3.3V            210    32    Volts    3.282000   

0 BB +5.0V STBY            211    32    Volts    4.980500   

0 BB +3.3V AUX            212    32    Volts    3.282000   

0 BB +1.05V P1Vccp            214    32    Volts    0.911700   

0 BB +1.05V P2Vccp            215    32    Volts    0.887700   

0 BB +1.5 P1DDR AB            216    32    Volts    1.495400   

0 System Event Log            7    32    UNKNOWN   

0 BB +1.5 P1DDR CD            217    32    Volts    1.509000   

0 BB +1.5 P2DDR AB            218    32    Volts    1.509000   

0 BB +1.5 P2DDR CD            219    32    Volts    1.502200   

0 BB +1.8V AUX            220    32    Volts    1.793600   

0 BB +1.1V STBY            221    32    Volts    1.076230   

0 BB VBAT            222    32    Volts    3.055900   

0 BB +1.35 P1LV AB            228    32    Volts    READING_UNAVAILABLE   

0 BB +1.35 P1LV CD            229    32    Volts    READING_UNAVAILABLE   

0 BB +1.35 P2LV AB            230    32    Volts    READING_UNAVAILABLE   

0 BB +1.35 P2LV CD            231    32    Volts    READING_UNAVAILABLE   

0 System Event            8    32    UNKNOWN   

96 NM Capabilities            26    44   

96 P1 MTT            52    44    %    

96 P2 MTT            53    44    %    

0 Button            9    32    UNKNOWN   

0 VR Watchdog            11    32    STATE_DEASSERTED   

My board is nearly 10 years old.  In the Intel pages,  there is one which lists Server Products, and for the SE7501HG2 there is a list of "Supported processors".

Intel� Server Board SE7501HG2 — Supported processors

To my big surprise I find brand-new Xeons in that list, e.g. under 3.00 GHz the E5-1607 v2.

Q.: is it really possible to upgrade that old board to a brand new Xeon?

Should the answer be yes, that would really please me.

Regards,

Ch

Hello,

I'm trying to get remote management working on an older SE7520BD2V server board with the Advanced Edition IMM module installed.

The IMM is configured and working properly as I can go to the configured IP in a browser and get the basic management options. I can also retrieve information from this system from a remote system with command-line IPMI tool.

However, I'm unable to connect from Intel Server Manager (ISM) 8.50. I can discover the IMM IP but when I try to connect, it complains with "Invalid IPMI BMC credentials. Please type in the correct user name and password."

I'm wondering if this could be because I'm running from Win7-64?

If not, what else can I try?

I tried to install the newer Multi Server Manager, but that requires IPMI/BMC on the system from which it's run. I only have ASF on this workstation board. Is there another Intel server management package that's newer than MSM?

Thanks,

Brad

Hi,

 

I am koteswararao working on intel based x86_64 board (ATCA-46xx) which has

HDD LED that indicates the status about HDD access . During HDD access

LED is 'ON'. But, after applying sgpio related patches specified in below link ,

the HDD LED is continuously 'OFF' and doesn't blink during HDD read/write operations.

 

The below commit's are backported from 3.2 kernel (kernel.org)

{{{

1.

8ec6552f4a77d15f446b00aed364e3c12d38aa6c

[SCSI] libsas: sgpio write support

 

2.

13257cfbc57e9cf84fd9fe0cb7a909b3fb4f7482

[SCSI] isci: fix sgpio register definitions

 

3.

ad4f4c1de80abdda5d55315289505598aa78e355

[SCSI] isci: initial sgpio write support

}}}

 

I have gone through the above commit code and observed that

SGPIO_HW_CONTROL macro defined in 3rd commit in above list

is causing the issue.  I referred C600 data sheet given in below link

 

http://www.intel.com/content/dam/www/public/us/en/documents/datasheets/c600-series-chipset-datasheet.pdf

 

to get idea over SGPIO_HW_CONTROL macro bit settings and observed

that LED issue is due to FSENG activity written in to SCU output data select register.

There is no much details about FSENG activity.

Could anyone please let me know more details about FSENG activity?

What does this FSENG activity means?

how it has effect on HDD LED (front panel LED)?

 

Thanks for allowing me in posting this mail.

 

Regards

koti46xx

Hello All,

I am trying to get the integrated BMC web console working on an S5520HCR mainboard.

I have assigned it an IP address, and I can ping the address and get a response.

When I navigate to http://<IP Address>, or to https://<IP Address>, I get that standard 550 error that the page cannot be displayed.

This is the first time that I have tried the intel system (sorry, but I have always used HP or Dell servers to date), but any help that you can offer would be appreciated.

Thanks in advance.

Nick

Hi!

I am doing my MSc thesis on a system which moves a huge amount of data to a PC through optical fiber.

I've bought E10G42BTDA wich mounts Intel 82599ES.

On the system side I have an FPGA.

I'm wondering if there is any DLL that I can use to read data coming from the FPGA.

I'm running C# code to read.

If not, how can I make it feasible?

Thank you!!

Regards,

Kaiyu Lin

I can't seem to find any specifications for the loudness of the fans in the P4304CR2LFKN. 

I'm looking to build a workstation that I would keep under my desk.  It would hold a tesla k20 and two e5-2695's for scientific computing (number crunching). 

It would need to be located in the office with me and noise is obviously a non-starter as we shop for options.

I like the W2600CR2 but searching high and low and I cannot find any noise specs for the air fans in P4304CR2LFKN or FXX1600PCRPS. 

Could someone please help? 

Thanks.

Hello,

     We are having an issue with our SR2612URR Intel server when you log into the MegaRaid for trouble shooting purposes it locks up on us and we are forced to power off the San.  After some digging we found that the USB is causing the issue, what we would like tod o is set up the SAN to boot up from a SSD drive instead of the USB.  My question is what drive would be good to use and if there are any instructions on how to do this?

Hello;

I just bought a S5000PSL board (used). i have 2 intel xeon cpus installed as well as 16gb ECC FBDIMM. I have reset the cmos as well as stripping it down to 1 DIMM and still no display.

When it POSTs i get this LED error code: Green, Red, Red, Amber. I checked the product documentation and it says that that code means "Disabling the console controller" I have no idea what that means.

Any help would be very appreciated.

Thank you for your time.