We have a Server with Integrated RAID Module RMS3CC040 (Firmware Package V: 24.21.0-0012, Firmware Version: 4.680.00-8249) with 3 Samsung 850 Pro Drives RAID 0 (HS)
Every Reboot the Controller shows 3 Warnings: Controller ID: 0 PD is not enterprise class self encrypting drive. Encryption capability of the drive will be disabled -:-:0
We Use AVAGo MSM 17.05.00.02
Any suggestions or ideas ? Thanks in advance.
Hi . Where I can get power 5V for SSD disk attached to sata port 4 on platform in 1208WTTGSR ?
Port 4 sata & port5 sata are inside platform (on image )
Due to inappropriate BIOS update (wrong update order) I've bricked the motherboard so it can't boot even from the backup.
As the warranty is expired I've send the board to the service center, but they need the full bios file (12MB) to flash it.
The CAP files in the firmware update are only 5MB and it's just an update files - not the full bios. Where can I get these files?
Hello,
I have a Buchanan Pass system with the S2600BPB motherboard (XXLRE chassis, HNS2600BPB compute module). An Intel PCIe M.2 SSD is attached to riser slot 2 (back). However, the SSD is not visible in the OS.
* BIOS version: SE5C620.86B.00.01.0009.101920170742
* OS: CentOS 7.4
It's not just one bad system - I have 2 chassis, 8 modules; same issue.
If I add HHHL PCIe SSDs (P4600 for example), I can see the drives as /dev/nvme* devices.
Is there a BIOS setting that is needed? I have tried both UEFI and Legacy boot options.
Board was working fine and disconnected from power for about an hour, now is completely dead. The green LED near the P1 power connection on the motherboard lights up but nothing else. No startup sequence or lights on the front, ID and power buttons do nothing.
Have also switched out the PSU in case that was the issue, no difference. No startup, no error codes, no beeps, nothing.
I see there was another thread in the forums with the same issue, but on a new build, with no resolution. Is this board a lemon? We have quite a few servers using this board which makes me very concerned.
Hi, downloaded RAID Web Console 3 from here Download Intel® RAID Web Console 3 for Windows*
- Install the GATEWAY server on a remote machine, can log in ok.
- Installed the RAID driver version (SAS v6.713.05.00 (Trimode wont load, even though its listed there doesnt appear to be drivers in the package for this card)) for the RMS3CC090 on a S1200SPOR server running Windows 10 Pro
- Installed the DIRECT AGENT service for RAID Web Console 3 on the above server.
Logging in to the GATEWAY server, then pressing "Re-discover servers", this remote Windows 10 S1200SPOR with the RMS3CC080 never shows up.
We have disabled the firewall on the Windows 10 system
We have disabled the firewall on the gateway server
Is there no way of adding servers to the gateway server?
All documentation for Intel RAID Web Console 3 says the RMS3CC080 is fully supported...
Many Thanks
Is it possible to control the chassis identity light from the front panel header in order to make it a appear solid? In effect I would like to be able to use this light to essentially 'beep' out a code as output by our application software. Our host OS is Debian 8, motherboard is an S2600CW2R.
I know that 'ipmi-chassis --chassis-identify=FORCE' (and '=TURN-OFF') can be used to flash the LED indefinetly, but this is at a 1Hz on/off instead of a steady light.
Hi,
Some basic facts first:
OS: WIndows Server 2016
Motherboard: SuperMicro X9SRi-F
Socket: LGA2011 E5-2600/E5-1600 v2
Chipset: Intel® C602 chipset
I have tried to install the following drivers from Intel's webpage:
But still I have some missing drivers according to the Device Manager.
It's the built in SAS controller that I seeam to be missing drivers for.
Hardware ID:
PCI\VEN_8086&DEV_1D6B&SUBSYS_062B15D9&REV_06
PCI\VEN_8086&DEV_1D6B&SUBSYS_062B15D9
PCI\VEN_8086&DEV_1D6B&CC_010700
PCI\VEN_8086&DEV_1D6B&CC_0107
And for what I can understand it's Intel's drivers that I need, so where can I find them?
Edit:
Also the Intel® Driver & Support Assistant (Intel® DSA) don't work on Windows Server 2016 why's that?
Prior to replacing the 3V battery on the mother board, this command: "Ipmitool lan print 1" returned useful information. Now the command returns: Invalid channel: 1.
Did I lose a configuration setting and if so, what change do I need to make?
Hello,
I have configured my BMC LAN for a static configuration using ipmitool. Once I was done I tried pinging it and didn't get a response. I noticed that my mac address was 00:00:00:00:00:00 but everything else looks correct. Has anyone seen this before or figured out how to correct it?
Intel Server Board - S7200AP
BIOS Version - S72C610.86B.01.02.0072.041620172102
#########
# ipmitool lan print 1
Set in Progress : Set Complete
Auth Type Support : MD5 PASSWORD
Auth Type Enable : Callback : MD5 PASSWORD
: User : MD5 PASSWORD
: Operator : MD5 PASSWORD
: Admin : MD5 PASSWORD
: OEM :
IP Address Source : Static Address
IP Address : XX.XX.XX.XX <-- omitted IP address
Subnet Mask : 255.255.255.0
MAC Address : 00:00:00:00:00:00 <--- WHY?
SNMP Community String : public
IP Header : TTL=0x00 Flags=0x00 Precedence=0x00 TOS=0x00
BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Disabled
Gratituous ARP Intrvl : 0.0 seconds
Default Gateway IP : XX.XX.XX.XX <-- omitted GW.
Default Gateway MAC : 00:00:00:00:00:00
Backup Gateway IP : 0.0.0.0
Backup Gateway MAC : 00:00:00:00:00:00
802.1q VLAN ID : Disabled
802.1q VLAN Priority : 0
RMCP+ Cipher Suites : 0,1,2,3,4,6,7,8,9,11,12,13,15,16,17,18
Cipher Suite Priv Max : Xaaaaaaaaaaaaaa
: X=Cipher Suite Unused
: c=CALLBACK
: u=USER
: o=OPERATOR
: a=ADMIN
: O=OEM
############
# ipmitool bmc info
Device ID : 33
Device Revision : 1
Firmware Revision : 1.00
IPMI Version : 2.0
Manufacturer ID : 343
Manufacturer Name : Intel Corporation
Product ID : 117 (0x0075)
Product Name : Unknown (0x75)
Device Available : yes
Provides Device SDRs : no
Additional Device Support :
Sensor Device
SDR Repository Device
SEL Device
FRU Inventory Device
IPMB Event Receiver
IPMB Event Generator
Chassis Device
Aux Firmware Rev Info :
0x01
0x07
0x40
0x28
Thank you so much for your help.
bom dia, apos atualizacao da bios, o led ambar fica piscando, diz que e as memorias incorretas mas no IASC todas estao OK.
Hi
We have connected a PCI-e display adapter (nVidia) inside this server, Windows 10 does not see any new hardware, we do not get any video from this adapter (on boot or Windows), we have the BIOS drivers loaded.
Are there any standards that need to be met in the new card for the system to see it? How can we tell in BIOS if it sees the new adapter?
The card we are testing (Jaton nVidia VIDEO-PX628GS-LP1), works in other Intel boards (DX79xx series).
Good Day.
I am tried enable "OS boot watchdog timer" at BIOS, but my OS (Window 10 - 1709) always rebooted.
I didnt find Intel Watchdog driver and i dont understand how i should install it.
I am really need your help.
How i should check this driver? Does this function support Windows 10?
| RMM Status : | Intel(R) RMM not installed |
| Device (BMC) Available : | Yes |
| BMC FW Build Time : | Mar 23 2017 20:14:24 |
| BIOS ID : | SE5C600.86B.02.06.0006.032420170950 |
| BMC FW Rev : | 01.28.10603 |
| Boot FW Rev : | 01.17 |
| SDR Package Version : | �� dd ddd |
| Mgmt Engine (ME) FW Rev : | 02.01.07.328 |
I use Intel's dual-server server S2600CP2 and Windows Server 2008 R2 operating systems. After installing the INTEL RSTE GUI, when setting up a mail reminder, after entering the SMTP mail server address and port and the sender and recipient email addresses, Send test mail each unsuccessful, for a lot of SMTP mail server address and port number, as well as the sender and the recipient's mail address will not work. And I was thinking, if you do not need to enter the login password of the mailbox, how can it send a test mail? I need to remind the function of mail, how should I properly set it, in order to normal use of the e-mail alert function.
Unless I am just not searching your support site properly, I have not been able to find any server firmware updates to address the microcode updates for Meltdown or Spectre or even any notification of a time line. I have a few Intel server that are hosting virtualized environments and would like to see these patched as all of my other server vendors have already delivered these updates.
Hello,
my Intel S1200SPL is in a third party case an I got problems with the fan speed. I have two PWM fans and one with 3 pin.
The Fans with PWM spin to slow and the 3 pin fan spin withe 100%. How can I fix this?
I allready made a SDR update and choose "Other Case" and set the fans.
Hi!
I have one RS3DC080 controller on win2016 srv with 8core 1.7GHz CPU.
I have installed Intel RAID Web Console 3 on it and i don't satisfied by that functionality.
Is it possible to automate sending log messages into syslog server or at least into the file using or without webconsole (w/o webconsole case would be preferable)? Now i see just manually log download button in web console.
I have found some log file in C:\Program Files (x86)\LSI\LSIStorageAuthority\logs but there is multiple repeated messages like:
13/04 18:56:29 11f0 | Error: Failed to free Memory
13/04 18:56:59 680 | Error: Failed to free Memory
13/04 18:57:29 11f0 | Error: Failed to free Memory
13/04 18:57:54 16e8 | Error: Failed to free Memory
13/04 18:58:29 11f0 | Error: Failed to free Memory
13/04 18:58:49 165c | Error: Failed to free Memory
13/04 18:59:29 11f0 | Error: Failed to free Memory
13/04 18:59:29 1200 | Warning: DCMD_FW_call_Info: ctrl=0 DCMD=0x2010000 status=0x0
13/04 18:59:29 1200 | Warning: DCMD_FW_call_Info: ctrl=0 DCMD=0x2010000 status=0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: SL_FW_call_Info: ctrl=0 SL_CMD_TYPE = 6 SL_CMD = 0 status = 0x0
13/04 18:59:29 1200 | Warning: DCMD_FW_call_Info: ctrl=0 DCMD=0x1010000 status=0x0
13/04 18:59:29 1200 | Warning: DCMD_FW_call_Info: ctrl=0 DCMD=0x1080101 status=0x0
13/04 18:59:45 6dc | Warning: DCMD_FW_call_Info: ctrl=0 DCMD=0x5010000 status=0x0
13/04 18:59:45 6dc | Warning: DCMD_FW_call_Info: ctrl=0 DCMD=0x5030000 status=0x0
13/04 18:59:45 6dc | Warning: DCMD_FW_call_Info: ctrl=0 DCMD=0x5050100 status=0x0
13/04 18:59:45 6dc | Error: Failed to free Memory
13/04 19:00:29 11f0 | Error: Failed to free Memory
13/04 19:00:40 1674 | Error: Failed to free Memory
13/04 19:01:29 11f0 | Error: Failed to free Memory
while in web console there is nothing erros\warnings:
Information
| 8 | Controller ID: 0 Alarm Enabled by user. | 6:48:37 PM,13 Apr'18 | |||
Information
| 7 | Controller ID: 0 Alarm Disabled by user. | 6:48:36 PM,13 Apr'18 | |||
Information
| 44 | Controller ID: 0 Time established since power on: Time: 2018-4-13T18:43:35 41 seconds | 6:43:35 PM,13 Apr'18 | |||
Information
| 505 | Controller ID: 0 Controller operating temperature within normal range, full operation restored. | 35 seconds from Reboot | |||
Information
| 547 | Controller ID: 0 Inquiry info of PD: Port 4 - 7:1:7 . Inquiry Info - Vendor: HGSTHUH728080AL5204 R5G8N1DV ; Model: HUH728080AL5204 R5G8N1DV ; Serial Number: ; Capacity: 7 TB | 34 seconds from Reboot | |||
Information
| 247 | Controller ID: 0 Device inserted Device Type : Disk Device Id: 15 | 34 seconds from Reboot | |||
Information
| 91 | Controller ID: 0 PD inserted : Port 4 - 7:1:7 | 34 seconds from Reboot | |||
Information
| 547 | Controller ID: 0 Inquiry info of PD: Port 4 - 7:1:6 . Inquiry Info - Vendor: HGSTHUH728080AL5204 R5G7R9LV ; Model: HUH728080AL5204 R5G7R9LV ; Serial Number: ; Capacity: 7 TB | 34 seconds from Reboot | |||
Information
| 247 | Controller ID: 0 Device inserted Device Type : Disk Device Id: 14 | 34 seconds from Reboot | |||
Information
| 91 | Controller ID: 0 PD inserted : Port 4 - 7:1:6 | 34 seconds from Reboot | |||
Information
| 547 | Controller ID: 0 Inquiry info of PD: Port 4 - 7:1:5 . Inquiry Info - Vendor: HGSTHUH728080AL5204 R5G7W1BV ; Model: HUH728080AL5204 R5G7W1BV ; Serial Number: ; Capacity: 7 TB | 34 seconds from Reboot | |||
Information
| 247 | Controller ID: 0 Device inserted Device Type : Disk Device Id: 13 | 34 seconds from Reboot | |||
Information
| 91 | Controller ID: 0 PD inserted : Port 4 - 7:1:5 | 34 seconds from Reboot | |||
Information
| 547 | Controller ID: 0 Inquiry info of PD: Port 4 - 7:1:4 . Inquiry Info - Vendor: HGSTHUH728080AL5204 R5G94X8V ; Model: HUH728080AL5204 R5G94X8V ; Serial Number: ; Capacity: 7 TB | 34 seconds from Reboot | |||
Information
| 247 | Controller ID: 0 Device inserted Device Type : Disk Device Id: 12 | 34 seconds from Reboot | |||
Information
| 91 | Controller ID: 0 PD inserted : Port 4 - 7:1:4 | 34 seconds from Reboot | |||
Information
| 547 | Controller ID: 0 Inquiry info of PD: Port 0 - 3:1:3 . Inquiry Info - Vendor: HGSTHUH728080AL5204 R5G86D9V ; Model: HUH728080AL5204 R5G86D9V ; Serial Number: ; Capacity: 7 TB | 34 seconds from Reboot | |||
Information
| 247 | Controller ID: 0 Device inserted Device Type : Disk Device Id: 11 | 34 seconds from Reboot | |||
Information
| 91 | Controller ID: 0 PD inserted : Port 0 - 3:1:3 | 34 seconds from Reboot | |||
Information
| 547 | Controller ID: 0 Inquiry info of PD: Port 0 - 3:1:2 . Inquiry Info - Vendor: HGSTHUH728080AL5204 R5G91HDV ; Model: HUH728080AL5204 R5G91HDV ; Serial Number: ; Capacity: 7 TB | 34 seconds from Reboot | |||
Information
| 247 | Controller ID: 0 Device inserted Device Type : Disk Device Id: 10 |
Hi,
I'm using a S1200SPLR board with an E3-1245v6 CPU (latest Firmware version 03.01.1029 installed)
I'm looking for the most basic SAS Module option with SAS 12 Gbps ports (that can operate without any RAID features active) so that the operating system has direct access to the hard drives for software defined storage solutions.
The S1200SPLR has a fourth expansion slot "SAS Module slot". However I'm unable to find a compatible SAS module for that motherboard. If you check the motherboard's product page under "Compatible Products" and "RAID Products", you only get regular PCIe add-in cards ("Low Profile MD2 Card"), nothing for that special SAS module slot.
Is there a product to supply the S1200SPLR's SAS module slot with a SAS 12 Gbps port?
Thank you very much for your help!
I can not configure a software RAID of 5 disks on the R1208WTTGSR platform. Need raid 10 + 1 hot spare. In the BIOS, sata (0-3 port) and ssata (0-3 port) are available. It turns out that 2 different baskets! Accordingly, a raid can be created from only 4 disks! How to combine them into one basket? To make a raid you can create from 5, 6, 7 disks !!!
First of all I apologize for incorrect English, I'm using google translator. I have a s1200btsr with Xeon processor, it was working normally, suddenly it started to make a strange noise like it had a cable twisted in the cooler.
I try to call it already starts with this noise, as if a cable was catching on the cooler, or a bursting speaker. It has no beep and does not turn on the corner leds.