Quantcast
Channel: Intel Communities : Discussion List - Servers
Viewing all 3923 articles
Browse latest View live
↧

S2400SC memtest86 UEFI bit fade errors

January 16, 2018, 7:14 am
$
0
0

I have a S2400SC motherboard. Testing approved RAM, Samsung M393B2G70BH0-YH9 16GB ECC Registered Memory, using the Memtest86 v7.4 UEFI, I get a flood of bit fade errors (Test 10). The Memtest86 forum suggested that it might be a known bug in the Intel BIOS. In another forum posting, I saw a similar problem reported on various Intel MBs in the S2600 series. One individual reported that setting the BIOS to Optimize for UEFI fox it for him, but trying that, I still get a lot of errors.

The cpu is Intel E5-2450L (supports ECC RAM), and only 1 cpu is installed on the MB. I ran the tests using 1 core. I ran it again with 64GB installed (4 x 16GB), and again got a result showing 1024 errors in Test 10 only. The summary report shows

Lowest Error Address: 0x3FFFE018 (1023MB)

Highest Error Address: 0x3FFFF814 (1023 MB)

Bits in Error Mask: 00000000FFFFFFFF

Bits in Error - Total: 32 Min: 0 Max: 32

Max Contiguous Errors: 2

 

Thanks for any help in sorting this out.

↧
Search

How to set up mail reminder in Intel RSTe?

February 27, 2018, 10:10 pm
$
0
0

I use Intel's dual-server server S2600CP2 and Windows Server 2008 R2 operating systems. After installing the INTEL RSTE GUI, when setting up a mail reminder, after entering the SMTP mail server address and port and the sender and recipient email addresses, Send test mail each unsuccessful, for a lot of SMTP mail server address and port number, as well as the sender and the recipient's mail address will not work. And I was thinking, if you do not need to enter the login password of the mailbox, how can it send a test mail? I need to remind the function of mail, how should I properly set it, in order to normal use of the e-mail alert function.

↧
↧

Fan control on S1200BTL using linux (opensuse)

February 19, 2018, 4:19 am
$
0
0

Hi, I have a xeon server board with 32GB ECC memory as workstation… and I'm annoyed about the loud fan…

 

# ipmitool sensor | grep -I Fan
Sys Fan 2        | 686.000    | RPM        | ok    | na        | 294.000   | 392.000   | na        | na        | na        
Processor Fan    | 0.000      | RPM        | cr    | na        | 0.000     | 0.000     | na        | na        | na        
System Fan 4     | 1078.000   | RPM        | ok    | na        | 294.000   | 392.000   | na        | na        | na        
Sys Fan 1        | 0.000      | RPM        | cr    | na        | 0.000     | 0.000     | na        | na        | na        
Sys Fan 3        | 588.000    | RPM        | ok    | na        | 294.000   | 392.000   | na        | na        | na 

 

I already disconnect "Processor Fan" but I don't want to disable "System Fan 4"

 

I have done some study and I think I can control Fan speed with the "ipmitool raw…" command… like I read

FAQ Entry | Online Support | Support - Super Micro Computer, Inc.

Question can you give me the IPMI raw commands to control all the fan's on S1200BTL

 

thank you :-)

↧

S2600CP4 board w/E5-26XX v2 Processors and PCIe Bus configuration.

March 4, 2018, 5:09 pm
$
0
0

Good evening,

Just wanted to verify before I purchase, that if I use E5-26xx v2 processors in a S2600CP4 that I can "adjust" a PCIe bus speed. I have a card that has a PCIe 3 bus, however the board has "throttled" that to PCIe 2.

 

Thanks much

Ray

↧

S2600IP4 Motherboard SAS and SATA mixed disk setup

March 5, 2018, 2:23 am
$
0
0

Hello,

 

We have an S2600IP4 motherboard with the on board C602 SATA/SAS controller. We would like to install 2 SAS 8Tbyte disks and keep the current 2 SATA disks.

If we buy the RKSAS8R5 (Purple) Upgrade key which is supporting 8 SAS disks, will we able to use the controller in mixed mode (2 SAS and 2 SATA disks)? We don't want to build RAID on these mixed disks, Just 1 RAID on SAS disks and another one on SATA disks separately.

 

Could someone please help us, is it possible to mix the drives on the same contoroller if the Upgrade key installed?

 

Thank you.

 

Maxim

↧
↧

server system s2600WFT

March 5, 2018, 6:05 am
$
0
0
  1. Where I can find list of Xeon Scalable CPU that support Optane SSD memory? I find several document like this https://www.intel.com/content/dam/www/public/us/en/documents/brief/xeon-scalable-processor-improves-hpc-performance-brief.pdf its write that support, and on other side on Intel ark for all Xeon Scalable family state that not support Intel Optane memory. I need clarification about Optane memory and Optane SSD? Is supported Intel Optane SSD working in memory pool or not? On Intel web portal is only example of desktop processor and system, nothing regarding server product, only thing I find is Win Server 2016 driver https://downloadcenter.intel.com/product/97160/Intel-Optane-SSD-DC-P4800X-Series
  2. Memory pool with Intel Optane P4800X, is it possible to create Intel Optane P4800X  with part of capacity in memory pool and rest use as data cache.  For example P4800X 375GB, use 250GB in memory pool with 16GB RDIMM and rest of 125GB to be used as data cache for NVMe disk in raid?? Or only is possible to add in memory pool complete capacity of 375GB, and  is not possible to partially be added?
  3. Where can find driver for add Intel Optane P4800X in memory pool, and how we can configure?
  4. When is used in memory pool Intel Optane P4800X can store data after power loss? If yes for how long?
  5. Is it possible to mirror Intel Optane P4800X SSD drive whit self  to split logically and have raid on one drive (one Intel Optane P4800X in system)??
  6. Which OS is supported whit Intel Optane P4800X? As I see only Windows Server 2016 driver exist?
  7. What is limitation on VROC boot domain regarding number of disk? For example is it possible to boot with raid 5 on five disk? Or is limited per domain disk support, as domain support only 4 disk and raid can be created only to those 4 disk to be able to boot.  Domain are  3 per CPU each with 4 disk on same domain, totally 12 disk to CPU.
  8. List of intel write intensive, and read intensive SSD? On ark is expressed as totally write per warranty time in PB, is there any doc that have write per day capability?
↧

S5000PSL turns off after running for few seconds & no vga signal

February 24, 2018, 12:38 pm
$
0
0

Hi,

 

This is my first time trying to build and I am no expert, so please understand if I ask for more details even for something simple. I have:

1) 2 x  Intel Xeon quadcore E5450 3Ghz 12MB L2 SLANQ

2) 32GB RAM (8 x  4GB, DDR2, 667, CL5, ECC)

3) Intel S5000PSL , PBA: E11027-102

4)SolidGear SDGR-750E , 750W PSU

5)2 x CoolerMaster HyperT4 cpu cooler (attached with metal wires)

6) 3 x 120mm case fans (3 pins)

7) no GPU for now

 

In the "pluggedins" image you can see that everything with a red mark means that I have something connected there. I have 2 problems. First one is there is no vga signal at all. Second one, is the LEDs issue. So, I turn the PSU, first the LED in "1" (PowerUpTry image) will be green then turn to half green and half amber ,eventually to solid amber. Now I press the power button of the case, after ~6 seconds it turns from amber in "1" to "2". After another ~6 seconds, it goes from "2" to "3" to "4" to "5" very quickly. It stays on "5" for ~ 6 seconds then the whole thing shuts down, all the fans stop working and end up with "6". During this process, the fans start to spin but dont make loud noise, after few seconds the noise becomes louder then few seconds later the noise becomes like how it was in the beginning eventually stop when the machine shuts down.

 

I tried installing one RAM stick at a time. I got the "beep" voice from 1 to 4 sticks for each time. But from 5 to 8 sticks there was no "beep" anymore. I tried 'one ram stick at a time' method with 2 cpus because it took me hours to place the cpu cooler right on the cpu and make it tight and firm. I hope it will be fixed without taking out the cpu.

 

I hope I can fix this up and run this machine eventually. Any knowledge or experience with this kind of issue is greatly appreciated. Please ask if something is not clear.

 

Thanks

↧

4K-native SATA HDD non-RAID support in S2600JF and S2600GZ systems with C600 series PCH

February 27, 2018, 12:48 pm
$
0
0

I have a few racks of S2600GZ, S2600JF, and S2600WT systems that currently use 512N/512E-formatted SATA HDDs in non-RAID mode (no Intel HW RAID, ESRT2, or RSTe - just ... JBOD) that we would like to continue supporting for our users for at least a few more years if not longer, but one of my concerns is the future availability of 512N/512E-formatted HDDs as 4K-native HDDs become the norm.

 

While the S2600WT systems are new enough to support 4K-native SATA HDDs, the S2600GZ and S2600JF systems are old enough that state of support for 4K-native formatted HDDs is not quite clear.

 

The bit of searching for info I've found only mentions support with Intel RAID (HW RAID, RSTe, ESRT2) which indicates a "pretty definite no" for that scenario but says nothing about our non-RAID HDD use.

 

Support for 4Kn and 512e Advanced Format Disks with Intel® RAID...

TA-1085-4: 4Kn and 512e Advanced Format with Intel® RAID and Intel®...

 

Will the C600-series PCH found in S2600JF/S2600GZ platforms support 4K-native formatted HDDs if used in non-RAID setups (just as plain SATA HDDs) or should I start strategically stockpiling 512N/512E formatted HDDs for the future?.

↧
Search

Intel® Server Board S1200SPLR - graphics

February 25, 2018, 5:40 am
$
0
0

intel server board s1200SPLR  needs a graphics card ?

 

Thanks.

↧
↧

Recovery bios s1200v3rps

February 5, 2018, 12:59 am
$
0
0

After updating the BIOS from 02.01.0002 to 03.04.0003 the BIOS is not loaded. In recovery mode, the BIOS starts. Backup BIOS also version 03.04.0003. How to restore the work of the BIOS?

I tried to install the R03.02.0003.cap and the old version from under the recovery mode. Writes to restart to install the update. Next, according to the instructions ( https://www.intel.ru/content/www/ru/ru/support/articles/000005630/boards-and-kits.html  ), I return the jumper back, but there is no result.

↧

S1200SPSR Diagnostic LED POST Progress Codes 0A ?

February 11, 2018, 3:51 am
$
0
0

Hello,

 

I have a problem, the new Serverboard S1200SPSR does not startet.

 

After Power on, Fans startet silent, the LED POST Code have:

 

green:

0=off

1=off

2=off

3=off

orange

4=off

5=on

6=off

7=on

 

The Intel Post Code say A0 and no action.

Interactive POST Code Diagnostic Decoder

 

When the Board is on, wait 20 second and then running all Fans maximum.

 

Here the System:

Board DBS1200SPSR Vers. H77897-271

CPU Xeon E3-1220V6

2x 4 GB Kingston KVR24R17S8/8 Bank A1/B1

4x SATA HDD 500GB Sata 0-3

1x DVD Rom Sata 4

Power 700Watt NitroX

 

Can you help me?

 

Klaus

↧

SAS SSD on MFS5520VI

February 27, 2018, 9:03 pm
$
0
0

Hello, I want to buy, SSD: Hitachi Ultrastar SSD800MH.B. and install in the MFS5520VI Server Module. Can I do that? Will the ssd work?

↧

C620 USB 3.0 2008R2 driver

February 15, 2018, 12:39 am
$
0
0

I'm looking for a W2K8R2 USB 3.0 driver for an intel C620 server board.

 

Capture.JPG

 

Is there any driver available yet?

↧
↧

RWC3 doesn't accept notification email addresses which contains "-"

February 18, 2018, 10:22 am
$
0
0

Hello,

 

I want to setup email notification in RWC3 and I'm not able to configure email addresses which contains "-" . I receive an error "Please enter a valid email id".

Is there a fix for this?

 

Thank you!

↧

server system s2600WFT

March 5, 2018, 6:05 am
$
0
0
  1. Where I can find list of Xeon Scalable CPU that support Optane SSD memory? I find several document like this https://www.intel.com/content/dam/www/public/us/en/documents/brief/xeon-scalable-processor-improves-hpc-performance-brief.pdf its write that support, and on other side on Intel ark for all Xeon Scalable family state that not support Intel Optane memory. I need clarification about Optane memory and Optane SSD? Is supported Intel Optane SSD working in memory pool or not? On Intel web portal is only example of desktop processor and system, nothing regarding server product, only thing I find is Win Server 2016 driver https://downloadcenter.intel.com/product/97160/Intel-Optane-SSD-DC-P4800X-Series
  2. Memory pool with Intel Optane P4800X, is it possible to create Intel Optane P4800X  with part of capacity in memory pool and rest use as data cache.  For example P4800X 375GB, use 250GB in memory pool with 16GB RDIMM and rest of 125GB to be used as data cache for NVMe disk in raid?? Or only is possible to add in memory pool complete capacity of 375GB, and  is not possible to partially be added?
  3. Where can find driver for add Intel Optane P4800X in memory pool, and how we can configure?
  4. When is used in memory pool Intel Optane P4800X can store data after power loss? If yes for how long?
  5. Is it possible to mirror Intel Optane P4800X SSD drive whit self  to split logically and have raid on one drive (one Intel Optane P4800X in system)??
  6. Which OS is supported whit Intel Optane P4800X? As I see only Windows Server 2016 driver exist?
  7. What is limitation on VROC boot domain regarding number of disk? For example is it possible to boot with raid 5 on five disk? Or is limited per domain disk support, as domain support only 4 disk and raid can be created only to those 4 disk to be able to boot.  Domain are  3 per CPU each with 4 disk on same domain, totally 12 disk to CPU.
  8. List of intel write intensive, and read intensive SSD? On ark is expressed as totally write per warranty time in PB, is there any doc that have write per day capability?
↧
Search

R2308WTTY not starting

March 6, 2018, 6:27 am
$
0
0

Hello,

 

I have a problem with the new server platform R2308WTTY. After power on i dont get any video, all the fans run at maximum speed

 

Specs:

Server platform R2308WTTY

MB S2600WT

2 x XEON E5-2630 v4

8 x KVR24E17D8/16

 

Error

POST error code 3 beeps

green:

0=on

1=on

2=on

3=off

orange

4=off

5=off

6=off

7=off

 

Can you help me?

↧

R1000SPO server series rail options (R1304SPOSHORR rails)

December 1, 2017, 2:59 pm
$
0
0

Hi

 

Using the server configurator for the R1304SPOSHORR server i get the below rail:

AXXVPSRAIL (cheap one)

 

I notice under ARK for the above server i can use:

AXXPRAIL (quick fit and supports CMA (according to ARK here 1U/2U Premium Rail AXXPRAIL Product Specifications).

However the above AXXPRAIL doesnt have a listed part for the Cable Management Arm (CMA), i did find AXXCMA2 but this isn't listed to fit this rail, traveling around the internet i found this AXX1U2UCMA, i assuming this is the one for the AXXPRAIL?.

 

We have a 24 inch rack (609.6mm), so will the below work:

R1304SPOSHORR

AXXPRAIL

AXX1U2UCMA

↧
↧

Intel Server System R2224WTTYS

February 10, 2018, 1:38 pm
$
0
0

Hello, i own two of these systems with Intel Server Board S2600WTT and im having serious issues booting them up

For cpu i use one Xeon E5-2609V4 in each and two sticks of Samsung M393A1G40EB1-CPB0Q reg. ecc 2133 ddr4 ram

 

basically the system starts with three beeps, fans spin at full and leds show an error (one green, three ambers) , black screen.

 

Could it be a compatibility issue with V4 cpu or even memory ? dont have much experience with Intel systems

↧

How do you remove plastic insert in toolless drivebay

March 6, 2018, 2:48 pm
$
0
0

I can't believe I have to ask this, but I can't figure it out and can't find any documentation. Our new Wolfpass servers came with 8 tool less 2.5 inch drivebays, and for the life of me I cannot figure out how I am supposed to remove the plastic inserts in the drive bays so I can actually use them. There really should be a diagram on the cover because it is certainly not intuitive how you get these things out. Where there normally would be the 4 screws, there are four little pieces of metal that look like they are supposed to be pressed, but how would someone press all 4 at once? This seems really stupid and I'll probably feel stupid when I find out the answer.

↧

Windows Server 2016 Mirror Created using Microsoft Disk Management

February 22, 2018, 5:06 am
$
0
0

Hi

 

Windows
Server 2016

Intel
s1200Splr Motherboard

2 x
1 TB Seagate 7200 rpm Drives

BIOS
set to Legacy

Santa
set to AHCI

Mirror
Created Using Windows Disk Manager Add Mirror Function

Mirror
Builds, says it is Healthy

Shutdown
System

Remove
Primary Drive

Boot
off Secondary

Boot
Fails No Drive Found

 

Tested
on another s1200SPLR motherboard with different drives, same result cannot boot
off secondary

 

Works
fine on all previous S1200, series boards

 

I
can be reached via email or voice at 4162047560

 

 

Sent
from my iPad



On Feb 21, 2018, at 10:47 PM, intel_corp <webadmin@intel.com>
wrote:

Intel Communities

 

Windows Server 2016 Mirror Created
    using Microsoft Disk Management

created
    by Intel
    Corporation in Servers - View the full
    discussion


   

   

Hello CalParsons,

 

   

 

    Thank you for contacting Intel Customer Support.

 

   

 

    I just check in our records and I don't see any similar incident in our
    records, so please allow me some time to go ahead and try to have this
    replicated, If you could provide some further details on your set up, like
    hardware models, software versions, steps followed to create and restore
    the mirrors that would be very helpful

 

   

 

    Please feel free to reply to his message at any time, I'll stay tuned to
    your comments.

 

   

 

    Regards.

 

   

 

    Kenneth R.

 

    Intel Customer Support

Reply to
    this message by going to Intel
    Communities

Start a new
    discussion in Servers at Intel
    Communities

This was sent to
    you because you are subscribed to Intel Communities. To unsubscribe from
    Intel Communities, click here.

© 2017 Intel
    Corporation

    Intel Corporation, 2200 Mission College Blvd., M/S RNB4-145, Santa Clara,
    CA 95054 USA. www.intel.com

Privacy | Cookies | Trademarks | Unsubscribe All

 

↧
Viewing all 3923 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>