Hello !
Acquired RAID controller MegaRaid SAS 9240-8i
When connecting to the Intel C2600CW2R motherboard and running the Windows Server 2008/2012/2016
(tried different versions), a problem arose:
The controller in the system is detected with an error: This device can not be started
(code 10): hardware error of the I / O controller
Location: Socket PCI 257 (PCI-bus 7, device 0, function 0)
The manufacturer of the device LSI Korp.
I ask to respond to mail: si@nerkon.ru
Hello everybody!
Here is the problem: dashboard shows this message: "Check Storage Controller Status". When I click the SCM2 in management interface it shows: "Initializing (Offline)".
Our distribuitor ended up support of this model.
Thank you in advance!
Hello everyone, first time posting here.
I am using the TPM 2.0 module AOM-TPM-9665 on a Supermicro X10SDV-TLN4F and I used the example AuthPolicy to provision it, through the uefi shell, and enabled TXT. I followed the instructions at [1].
I did that in order to better understand how I can provision TPM. But now I have created a new AuthPolicy with a custom pass phrase and I want to use this one. The problem is that when I try to clear the old authPolicy, when I run `ResetPlatformAuth.nsh sha256 EXAMPLE` I get the error "Did not satisfy PlatformPolicy Provisioning FAILED Setting PlatformAUth to EMPTY failed". What am I missing? Any suggestions?
I am pretty sure I haven't understood something correctly. If anyone can point me on where I can get more documentation on the correct usage of TPM, I will be grateful.
Hi. I have a server that uses 3-3 Terabyte drives to create a RAID 5 system for data. Had a crash and the Intel manager software said it fixed the problem but Windows Server 2008 R2 does not see it as a drive anymore. Just un-allocated. I need the data off the RAID! Any help please.
Hi I need to install Intel Accelerates Storage Manager to Windows Server 2016 Core and mainly to silently configure monitoring/sending emails when problem with HDD occured. I didnt find any manual, that told me how to do this? I see that there is some new feature (web ui), that maybe can be used to this? But I am not able to authenticate to it using local account..
Hi guys. Building a server used for SOHO back office and high end test/devel
I want the board to support ESXi 6.5 fully NICS, I/O passthruough. Furthermore it should:
1) have IPMI/iKVM
2) Support at least 64 GB DDR4, preferable 128 GB
3) low power usage
Any suggestions?
Regards, Lars.
We have a part number :
SVCEWUPSY
What does this cover? is it the complete server (board, CPU, case including PSU, backplanes and hard drvie carries?) my point is, Lenovo offer warranty upgrades and it covers EVERYTHING in the server including CPU, RAM (if its Lenovo), Hard drives (also if Lenovo) and ALL hardware parts.
How do Intels work?
The above is 2 years, can we get longer? Does it have to be ordered with the server or can it be done anytime in the first year?
Is this part number only for the R1200SPO hardware or is it on the S1200SPO generation of boards?
Hello ,
I reading the CRPS design guide about PMBus Black box Command
The meaning as below:
Name: MFR_BLACKBOX
Format: Read Block with PEC (238 bytes)
Code: DCh
The content have "System Tracking Data(47 bytes)" and "Power supply event data(38 byte per event)",
and the "Power supply event " can record 5 event,
so.. the total length of the command as 47 bytes + (38 bytes *5 ) = 237 bytes,
I calculated the result with the design guide length is not equal (238 byte ≠ 237bytes),
Is anyone knew the correct format about this command(DCh) , or can tell me what's detail I missed?
Alan Chen,
Hello
I have a server workstation board and I am experiencing a system freeze with a CPU_CATERR -
I am trying to understand the data in the system event log to see if it will point me in the right direction:
I tried using the document here:
System Event Log Troubleshooting Guides for Intel® Server Boards
but to no avail.
BMC-Owned Sensors (GID = 0020h) Section 3.1 Table 5 Does not have an entry for 0xDA.
Can anyone shed some light on this?
Board Has A C612 Chipset with 2 xeon E5 V4 2630 Processors on it.
Complete Info From the SEL Data:
04 00 02 2C A1 18
5A 20 00 04 07 DA
6F 00 FF FF
SENSOR # 0xDA
CPU_CATERR
Event Description IERR
RECORD TYPE 0x02
Thank You
Dear Sirs,
any idea whether there are cables available that will support the following? Have to use 3rd party Chassis.
1) RSP3TD160F to direct attach P4500 SSD series (SFF-8643 to SFF-8639 plus power). It seems that the broadly availabe cables with these specifications don't work. When using a PCIe Interface Card the SSDs are recognized, but when using Raid Card they are not. Heard about cables called "U.2 enabler cable". Anybody heard of it?
2) RSP3TD160F to a backplane using SFF-8643 for NVMe drives. Same Problem.
Hope anybody can give a hint.
Regards,
Sven
after i have disabled onboard VGA,
I'm unable to enable again,
even if i enable it in bios it still dont work
Listed below are the Queries,
1. Are the System Boards ( Interface Cards) Similar to the ones in a 2U system Or are the HPC node based System Card's Different ?
2. Related to the HSBP of the 4 Node S2600BP - can you provide us with relevant Detailed information?
3. Are there Any Details Of the Chassis Drawing or Suppliers That we Can Get in touch with?
Awaiting for a Response.
ZAID
VEPL, INDIA
We have one server with S2600CW2 board and it has few issues with LAN port1:
When restarting server, BMC link fails for some period and then up again.
Using LAN port 1 not possible to do anything.
Have to use LAN2 and MGMT port to be able to do anything.
When trying to boot to PXE using LAN1 port, then it fails for many first attempts.
Can it be port 1 failure and need to change motherboard?
FW is the latest and greatest
Hope for hint and advice!
Can one use (install) two of FUP8X25S3NVDK in ONE P4304XXMUXX?
E.G. by using a Broadcom MEGARAID 9460-8I
If yes, will there be 4, 8, 16 nvme ssd usable?
Hello,
I have a S2600CP2 board with a AMD R9 380 GPU installed on a pcie x8 slot. It work fine is EFI optimized boot is disabled. But as soon as I turn that on, it can't p*** the board self-check. The diagnosis led light as the image
well, i had set Use Legacy Video for EFI OS to enabled but no working.
Any solutions?
Many thanks.
I picked up a s2600cp that I am trying to get running. I have got the BIOS updated to the latest version (02.06.0006) after stepping through many upgrades. I have 3 4pin fans plugged into system fan 1, 2 and 3. I ran frusdr and configured those fans, all other fans off, and marked no for chassis intrusion. Upon completing the config update the fans immediately spin down, but after the BMC reinitialized they ramp back up to full speed. I ran sysinfo and after digging through the log saw this:
Management Subsystem Health, BMC FW Health (#0x10) Warning event: BMC FW Health reports the sensor has failed and may not be providing a valid reading.
It I dug deeper and found that it started popping up somewhere during the bios updates(The version that I started with was so low i stepped through maybe 12 to be safe). After seeing this I reflashed the BMC, and reflashed frusdr to no change.
I have found very little after scouring the net for this error. I have seen some people say this means the board is failing, and I have seen some people say it means its reading something wrong. Either way both pieces seem a bit vague.
I am fairly certain this is the cause of the full speed fans as the system status LED is flashing green and I believe a fault like this will trigger fans to run at max speed.
Also the system seems to be running fine other than this. Does anyone have any information that could shed some light on this? Thanks
We have compute nodes with 24 cores( 48 threads) and 64 GB RAM (2x32GB). When I run a sample code (matrix multiplication)in one of the compute node in one thread, it takes only 4 seconds. But when I starting more runs (copy of the same program) in the same compute node, the time taken increases drastically. When the number of programs running reaches 24 (I gave maximum 24 since physically only 24 cores are present), the time taken becomes like around 40 seconds ( 10 times less). When I checked the temperature, it is below 40 deg Celsius.
When I searched in the Internet about this issue, I found some people saying that it may be due to slowing down of transfer of data from ram to processor when we run many programs. I was not satisfied with this comment, because the compute nodes are designed to run at maximum load with out much decrease in performance. Also, we are using only 1GB of memory even with 24 programs running. Since we are getting performance reduction of about 1/10, I guess the problem is something else.
How to fix my customer's Switch Module SW1 on Intel Modular Server MFSYS35 from bootloop ?
Here is the detail :
- the green led is blinking for a long time
- the orange led is steady for a long time
- when I see the terminal connection on serial (RS232 port) with telnet :
"
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.6 Built 30-May-2007 11:09:42
Intel ClearBay board, 88F5181 CPU based with ARM926EJ-S core.
128MByte SDRAM. I-Cache 32 KB. D-Cache 32KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-1
100%
OK
Running from RAM...
*********************************************************************
*** Running SW Ver. 1.0.0.27 Date 21-May-2008 Time 10:42:27 ***
*********************************************************************
HW version is
Base Mac address is: 00:15:17:4f:94:e6
Dram size is : 128M bytes
Dram first block size is : 102400K bytes
Dram first PTR is : 0x1800000
Dram second block size is : 4096K bytes
Dram second PTR is : 0x7C00000
Flash size is: 16M
01-Jan-2000 01:01:06 %CDB-I-LOADCONFIG: Loading running configuration.
01-Jan-2000 01:01:06 %CDB-I-LOADCONFIG: Loading startup configuration.
Devices on PCI BUS 0 (slot 0):
-----------------------------
id select = 31, dev type=0x5181
Device configuration:
---------------------
Slot 1 : AXXSW1GB
HW revision : D70739-404
CPLD ID : 128
CPLD Version : 2
Slot ID : 0x1
IDROM size : 103Bytes
ESM Module ID: 0.46
01-Jan-2000 01:01:08 %2SWINIT-F-INITCOREPPHWPHASE1: SW2P_core_pp_hw_phase1_init: Core PP HW phase 1 init failed - error msg Operation failed
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 1.0.0.27 (date 21-May-2008 time 10:42:27)
**************************************************
***************** SYSTEM RESET *****************
**************************************************
"
the hardware bootloop continuosly
intel s1200sps mainboard has the i2c ( SSI compliant 1x5 pin connector J9F1 to provide I2C monitoring of the power supply. https://www.intel.com/content/dam/support/us/en/documents/server-products/S1200SP_TPS_R1_1_S1200SPL_S1200SPS_S1200SPO.pdf) connector to track failures from psu on intel's own supported cases.
Has anyone managed to get supermicro's PDU (for example PWS-721P-1R) information of power failures?
When I test to plug out power cable I get OK readings from intel's bmc:
Name  | Status | Health | Reading |
|---|---|---|---|
| Pwr Unit Status | All deasserted | OK | 0x0000 |
Br, Max
I have a Wolf Pass 2600WFT Server where I am trying to load a DPDK-assisted vSwitch as I do on the Wild Cat Pass.
But DPDK fails to load because the Ethernet port is on PCIe domain 10000, instead of the normal 0000.
Is there some BIOS setting or update to make the domain for this Fortville NIC to be enumerated in domain 0000 ?
# ovs-dpdk -c 0x5 -n 4 -r 2 --socket-mem 1024,1024 --huge-dir /mnt/huge-1048576kB --file-prefix vs --proc-type primary -w 10000:01:00.0
DPDK failed to allocate requested resources...
# lspci | grep Eth
0000:3d:00.0 Ethernet controller: Intel Corporation Ethernet Connection X722 for 10GBASE-T (rev 09)
0000:3d:00.1 Ethernet controller: Intel Corporation Ethernet Connection X722 for 10GBASE-T (rev 09)
0000:af:00.0 Ethernet controller: Intel Corporation Ethernet Controller X710/X557-AT 10GBASE-T (rev 01)
0000:af:00.1 Ethernet controller: Intel Corporation Ethernet Controller X710/X557-AT 10GBASE-T (rev 01)
0000:af:00.2 Ethernet controller: Intel Corporation Ethernet Controller X710/X557-AT 10GBASE-T (rev 01)
0000:af:00.3 Ethernet controller: Intel Corporation Ethernet Controller X710/X557-AT 10GBASE-T (rev 01)
10000:01:00.0 Ethernet controller: Intel Corporation Ethernet Controller X710 for 10GbE SFP+ (rev 01)
10000:01:00.1 Ethernet controller: Intel Corporation Ethernet Controller X710 for 10GbE SFP+ (rev 01)