Hello

I apologize in advance for the presentation of the text, write in Russian and translate in the browser.

Asking for help from professionals. Platform "R1304SPOSHBN", fully assembled, all components are in their places, the processor is "XEON E3-1230 v6 ", RAM 2*16GB Kingston KVR24E17D8/16MA

The problem is that when the system starts the testing begins, the fan speed maximum rpm is reduced to minimum and testing apparently ends, then should start to boot the system (?), however on the screen nothing appears either during testing or after. However, after the fall of the fan speed, about 30 seconds later the server rebooted, then again and again. The screen is totally unresponsive. Apparently the problem with the built-in graphics card, but connecting the external new and serviceable graphics card has not produced results. BIOS reset.

In this case, can advise? How to diagnose the problem? The server is brand new, probably made a mistake somewhere with the connection of the components, but did everything according to instructions.

Help Board!

Hello everyone!

Could you tell me what raid controller models will be able to replace my RS2BL080 as hot spare/cold spare reserve (it must pick upexisting array ) , if it will die?

At the moment i can't find any RS2BL080 nowhere on sale.

There is must be some unified data format, to not attach to a particular raid controller model, don't it?

Dear Intel Support,

My system has following configuration: Mainboard S2600CW2R, Chassis P4304XXMUXX with two PSUs FXX750PCRPS, two CPUs Xeon E5-2637V4, Memory 8 modules each 16GB, one SSD DC S3520 Series 480GB, one HDD Seagate 3.5" 8TB ST8000NM0045 and Graphic Card ASUS GTX 1080 Ti.

OS: Windows 10 Pro. All firmware was initially updated to the newest version.

System works properly, passes all tests, OS boots and runs OK.

When starts 3D modelling software Bentley Context Capture and Graphic Card is in full load, system is suddenly shutting down with beep code 1-5-4-2.

PSUs are in FULLY_REDUNDANT state.

Looks like insufficient PSU resources.

"S2600CW_H56450_P4304XXMXXX_power budget_tool R1.1" tells that there is enough PSU resources: System Totals: 647W; Power Supply Limits: 750W.

Could you please advise me what the possible cause of system shut down and which actions to be taken to resolve situation?

Maybe to set PSUs in NON_REDUNDANT state to gain available power resources?

But I've found none information in a lot of manuals available how can I make it.

Thanks in advance.

Ich habe das S5500BC, Intel zeigt an, dass ein BIOS-update vorhanden ist. Die Installation schlägt immer fehl "unbekannter Fehler bei der Installation".

Was mache ich falsch? Firewall??

I have a RAID 1 volume on an Intel S1200BTL server board using the Intel Desktop/Workstation/Server Express Chipset SATA RAID controller (driver version 10.5.0.1029) that runs Windows Server 2008 R2. 

Sitting in front of the server (something I do very rarely as I remotely administer this box), I notice that the RAID BIOS showed that the volume was "degraded".  The BIOS utility only gives options for configuring the volume.  I am looking for a GUI that will tell me what is going on with the volume.

I downloaded the RST and AHCI Driver and GUI installation and launched the "iata_cd.exe" from the GUI folder after extracting the download from Intel's site.  This stated that it would install drivers as well as the software component.  I installed it on a test box and it prompted for a reboot, which I was unsure of whether it wanted a reboot because of a driver update.  The test box was a desktop that had the SATA AHCI controller on it, but it rebooted fine after installing.

This is a server for a small business and I can't take any chance that it will not boot back up because of a bunged driver.  I need to get some visibility into what is happening with this volume.  Any ideas the best route to go?

Thanks.

Can someone tell when what is the UN Dangerous Good classification for AXXRSBBU8 when it is shipped as a standalone spare unit by air?  It will be helpful if someone can provide the Safety Data Sheet for this product.

Has anyone come a cross this issue or a similar issue.

Here is what we are seeing. For no reason at all that we can see the fans while throttle up to high speed and remain "screaming" until the server is restarted. The problem is random but does happen on a regular basis. The system has all the latest firmware, it is running 32GB DDR4 2133 RAM E3-1230V6 (similar problems with 1230V5). L1 support tells me it is a memory issue because the memory isn't Intel validated. The RAM in use is Crucial and is guaranteed compatible. I am sure many of us use Crucial RAM and excellent results. Intel insists that non validated memory is causing the problem yet cannot provide me with a source to get this "validated memory".  The Intel support guy is really trying his best but so far, results are mediocre.

Any input will be helpful.

I have a server with the S2600CW2 board whose BMC web console I can access over HTTP.

When I try to access it over HTTPS, it does not respond however.

What could be the cause of this and what else can I do to troubleshoot/resolve it?

I am trying to install Windows 7 Pro x64 to Intel dbs1200splr.

I need to enter username and PC name during installing but i can't. Keyboard and mouse are not working in any USB ports(2.0 or 3.0). There is no PS/2 port to try another keyboard.

In BIOS or WinPE keyboard and mouse are normally works, no troubles.

So, How i can to install Win7?

Does the S2600WT2 support VMWare DirectPath I/O with ESXi 6.5?

thanks

Steve

Hi All,

I checked the compatibility of this board and it shows that it supports Esxi6.5U1, but when I was installing, Esxi6.5 U1 can only find those individual hard disks, not the RAID volumes I created via RSTe.

reference:    https://www.vmware.com/resources/compatibility/pdf/vi_systems_guide.pdf

Do I need to customize the ISO ? thanks              

Hello fellows,

I have one question on Hyper-threading ,Is it possible to enable/disable hyper-threading without using bios settings e.g. using syscfg and without rebooting server ? because i'm working with plenty of servers so it is not possible to enable individual server for HT it needs time and lots of work.

need some suggestions.

Hi,

I wanted to update the firmwares on a S2600CP that I've just started supporting. I previously installed Windows Server 2012 R2 on it and configured it as a Hyper-V Host and moved some VMs on to it and that was all working fine for a couple of weeks, including everything reporting as OK in the ASC.

So I tried to go to the latest firmwares (02.06.0006) via the EFI Shell and it failed the BMC update, at the end it said it could not leave Firmware Update mode and go back to Operation Mode.

I was on very old firmwares to begin with so I stepped through around 6 firmware bundles up to the very latest. When I booted into Windows I noticed the fans did not die down. I went into the ASC and could see the information attached in the images.

I tried downgrading back to the firmware before, which is what it's still currently on (02.06.0005) but this has not changed the situation.

Could anyone please help? Thanks.

I've purchased an Intel server from a authorized vendor, and want to update the mainboard firmware to the latest.

The mainboard is a S2600CW2R. According to the online analyzer, my firmware is:

I've looked at the firmware download page, and discovered that my firmware is rather old. 

Two questions:

1) Can I simply install the latest firmware? Or do I have to install every revision since the one installed?

2) There is something called a "FRUFIX" (Download Intel® Server Board S2600CWR FRUFIX Utility ) - Do I need it for my mainboard?

Any help would be greatly appreciated.

Bill

I'm looking to make a Virtualization Home Lab. I want to eventually run the router as a VM along with a Web- + Mailserver.

I learned I need SR-IOv functionality. Now I wonder if this mobo above has SR-IOv (Single Root IO Virtualization) support?

What other things do I have to be aware of beyond the mobo supporting SR-IOv?

I am in the process of setting up a ThinkServer TD350 with a Intel Xeon E52650V3 2.3Ghz Processor, and a TD-350/E5-2600 Motherboard, 16GB of 2R x 4 PC4 1700R RDIMM RAM.

The server is running Windows Server 2016.  BIOS and TDM (Thinkserver Deployment Manager) were both updated prior to installing the O/S and before attempting the chipset update.

From the device manager it shows "Intel(R) C610 series/X99 chipset SMBus Controller 8D22 Version 10.1.2.19  Dated 1/26/2016"

According to Lenovo's suggested downloads I am to install the Intel DD_INTEL_CHIPSET_10.1.2.77_Public_Win_x86x64.   

Installing this update caused the server to go Blue Screen with the error code: WHEA UNCORRECTABLE ERROR, for which the server gathered information and rebooted.

Lenovo suggested I download and run a (Microsoft Partnered) utility named Winthrust by Avangate/Solvusoft to clean up the registry, unused dll files etc.  The program was to have 25 free uses.  When I tried to apply the removal of said problems, it popped up a message that the free trial was expired and I had to buy the product, which I did for $30.00.  I then found out from a Malwarebytes scan that this "utility" has a red flag warning that it is malware/spyware.  I promptly removed the product. In a search I found numerous mentions that the Winthrust software utility and Avangate/Solvusoft was marketing a spyware product.

I have also run the Intel driver update utility.   The Intel utility displayed that there was a suspended driver installation and that it should be removed.  I allowed the Intel driver utility to clean things up.   The Intel utility then indicated that there were NO driver updates needed.

I again tried to install the chipset update and the system went blue screen again with the same error.  After the system rebooted I again ran the Intel driver update utility in which it again indicated that there was a suspended driver installation.

I now believe that the employees at Lenovo who have answered my questions about this problem do not have the correct information.  Advising customers to download known malware/spyware for use indicates that Lenovo support may not have their customer's best interests in mind.

I have a new Server Board S2600CP4 with 2 new XEON Prozessor E5-2660 v2 and 2 new INTEL Thermal Solution STS200C Fans. The sytem is working ok, but all fans are running full speed. Chassis intrusion is switched on.If I change anything in the bios for the fans, nothing happens, all time full speed of the fans. Has anyone an idea, what I can check? Thank you for help. Michael

Can someone tell when what is the UN Dangerous Good classification for AXXRSBBU8 when it is shipped as a standalone spare unit by air?  It will be helpful if someone can provide the Safety Data Sheet for this product.

Is there anywhere that I can access drawings for a server chassis, server board, and compute module?

Thank,

Jordan Parker

Hey there,

I cant quite seem to figure out why my fans seem to hate me. The PCI domain fan constantly speeds at 3,500 RPM regardless of what i change and I believe it should be spinning at around 1000-1400 compared to what other people have reported but mine refuses to go down to that level. I have quite mode enabled so the CPU domain fans are spinning very slowly which is correct.

The event log shows no obviously errors and all the sensors are green, only a few are not available. The bios, me, bmc, sdr are all updated with the latest versions as well.

Is someone elses info where it shows 1218 RPM which i would love to have.

[code]

001a | Full | Fan | 30 | System Fan 1 | OK | 1218.00 RPM

001b | Full | Fan | 31 | System Fan 2 | Init | 0.00 RPM

[/code]

Mine however is like this...

[code]

➜ ~ ipmitool sensor

Pwr Unit Status | 0x0 | discrete | 0x0000| na | na | na | na | na | na

IPMI Watchdog | 0x0 | discrete | 0x0000| na | na | na | na | na | na

Physical Scrty | 0x0 | discrete | 0x0000| na | na | na | na | na | na

FP NMI Diag Int | 0x0 | discrete | 0x0000| na | na | na | na | na | na

SMI Timeout | 0x0 | discrete | 0x0000| na | na | na | na | na | na

System Event Log | 0x0 | discrete | 0x0000| na | na | na | na | na | na

System Event | 0x0 | discrete | 0x0000| na | na | na | na | na | na

Button | 0x0 | discrete | 0x0000| na | na | na | na | na | na

VR Watchdog | 0x0 | discrete | 0x0000| na | na | na | na | na | na

SSB Therm Trip | 0x0 | discrete | 0x0000| na | na | na | na | na | na

BMC FW Health | 0x0 | discrete | 0x0000| na | na | na | na | na | na

System Airflow | 70.000 | CFM | ok | na | na | na | na | na | na

BB EDGE Temp | 25.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na

Front Panel Temp | 24.000 | degrees C | ok | na | 0.000 | 5.000 | 50.000 | 55.000 | na

SSB Temp | 43.000 | degrees C | ok | na | 0.000 | 5.000 | 98.000 | 103.000 | na

BB BMC Temp | 36.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na

BB P2 VR Temp | 34.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na

BB MEM VR Temp | 33.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na

HSBP 1 Temp | 25.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na

LAN NIC Temp | 48.000 | degrees C | ok | na | 0.000 | 5.000 | 115.000 | 120.000 | na

System Fan 1 | 3500.000 | RPM | ok | na | 392.000 | 462.000 | na | na | na

System Fan 2 | na | RPM | na | na | 400.000 | 460.000 | na | na | na

HSC1 Status | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P1 Status | 0x0 | discrete | 0x8000| na | na | na | na | na | na

P2 Status | 0x0 | discrete | 0x8000| na | na | na | na | na | na

P1 Therm Margin | -59.000 | degrees C | ok | na | na | na | na | na | na

P2 Therm Margin | -60.000 | degrees C | ok | na | na | na | na | na | na

P1 Therm Ctrl % | 0.000 | percent | ok | na | na | na | 30.000 | 50.000 | na

P2 Therm Ctrl % | 0.000 | percent | ok | na | na | na | 30.000 | 50.000 | na

P1 ERR2 | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P2 ERR2 | 0x0 | discrete | 0x0000| na | na | na | na | na | na

CATERR | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P1 MSID Mismatch | 0x0 | discrete | 0x0000| na | na | na | na | na | na

CPU Missing | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P1 DTS Therm Mgn | -59.000 | degrees C | ok | na | na | na | na | na | na

P2 DTS Therm Mgn | -60.000 | degrees C | ok | na | na | na | na | na | na

P2 MSID Mismatch | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P1 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P2 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P1 MEM01 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P1 MEM23 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P2 MEM01 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na

P2 MEM23 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na

DIMM Thrm Mrgn 1 | -33.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na

DIMM Thrm Mrgn 2 | -41.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na

DIMM Thrm Mrgn 3 | -43.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na

DIMM Thrm Mrgn 4 | -42.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na

Mem P1 Thrm Trip | 0x0 | discrete | 0x0000| na | na | na | na | na | na

Mem P2 Thrm Trip | 0x0 | discrete | 0x0000| na | na | na | na | na | na

Agg Thrm Mgn 1 | -30.000 | degrees C | ok | na | na | na | 0.000 | 0.000 | na

Agg Thrm Mgn 2 | -26.000 | degrees C | ok | na | na | na | 0.000 | 0.000 | na

BB +12.0V | 11.883 | Volts | ok | na | 10.635 | 10.947 | 13.027 | 13.391 | na

BB +5.0V | 5.046 | Volts | ok | na | 4.460 | 4.590 | 5.415 | 5.566 | na

BB +3.3V | 3.354 | Volts | ok | na | 2.953 | 3.039 | 3.554 | 3.654 | na

BB +5.0V STBY | 4.937 | Volts | ok | na | 4.460 | 4.590 | 5.415 | 5.566 | na

BB +3.3V AUX | 3.296 | Volts | ok | na | 2.953 | 3.039 | 3.554 | 3.654 | na

BB +1.05V P1Vccp | 1.146 | Volts | ok | na | 0.546 | 0.564 | 1.464 | 1.506 | na

BB +1.05V P2Vccp | 0.804 | Volts | ok | na | 0.546 | 0.564 | 1.464 | 1.506 | na

BB +1.5 P1DDR AB | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na

BB +1.5 P1DDR CD | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na

BB +1.5 P2DDR AB | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na

BB +1.5 P2DDR CD | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na

BB +1.8V AUX | 1.785 | Volts | ok | na | 1.644 | 1.702 | 1.902 | 1.960 | na

BB +1.1V STBY | 1.071 | Volts | ok | na | 0.938 | 0.964 | 1.240 | 1.276 | na

BB VBAT | 3.158 | Volts | ok | na | 2.211 | 2.544 | na | na | na

BB +1.35 P1LV AB | 1.336 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na

BB +1.35 P1LV CD | 1.348 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na

BB +1.35 P2LV AB | 1.354 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na

BB +1.35 P2LV CD | 1.348 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na

HDD 0 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

HDD 1 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

HDD 2 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

HDD 3 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

HDD 4 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

HDD 5 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

HDD 6 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

HDD 7 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na

NM Capabilities | 0x7f | discrete | 0x0300| na | na | na | na | na | na

P1 MTT | 0.000 | percent | ok | 0.000 | 0.000 | 0.000 | 0.000 | 0.000 | 0.000

P2 MTT | 0.000 | percent | ok | 0.000 | 0.000 | 0.000 | 0.000 | 0.000 | 0.000

[/code]