Hello everyone!
Could you tell me what raid controller models will be able to replace my RS2BL080 as hot spare/cold spare reserve (it must pick upexisting array ) , if it will die?
At the moment i can't find any RS2BL080 nowhere on sale.
There is must be some unified data format, to not attach to a particular raid controller model, don't it?
I'm looking into powering the S2600TPR motherboard in a 3rd party chassis. I noticed that there are two main power connectors and an auxiliary power connector as well. I was wondering if there was an adapter to connect power to this motherboard using an ATX power supply? If so what is the part number? If there is no power adapter cable how can I go about powering it?
Hi,
I wanted to update the firmwares on a S2600CP that I've just started supporting. I previously installed Windows Server 2012 R2 on it and configured it as a Hyper-V Host and moved some VMs on to it and that was all working fine for a couple of weeks, including everything reporting as OK in the ASC.
So I tried to go to the latest firmwares (02.06.0006) via the EFI Shell and it failed the BMC update, at the end it said it could not leave Firmware Update mode and go back to Operation Mode.
I was on very old firmwares to begin with so I stepped through around 6 firmware bundles up to the very latest. When I booted into Windows I noticed the fans did not die down. I went into the ASC and could see the information attached in the images.
I tried downgrading back to the firmware before, which is what it's still currently on (02.06.0005) but this has not changed the situation.
Could anyone please help? Thanks.
I am trying to install Windows 7 Pro x64 to Intel dbs1200splr.
I need to enter username and PC name during installing but i can't. Keyboard and mouse are not working in any USB ports(2.0 or 3.0). There is no PS/2 port to try another keyboard.
In BIOS or WinPE keyboard and mouse are normally works, no troubles.
So, How i can to install Win7?
I have a new Server Board S2600CP4 with 2 new XEON Prozessor E5-2660 v2 and 2 new INTEL Thermal Solution STS200C Fans. The sytem is working ok, but all fans are running full speed. Chassis intrusion is switched on.If I change anything in the bios for the fans, nothing happens, all time full speed of the fans. Has anyone an idea, what I can check? Thank you for help. Michael
We have a intel server MFSYS25 V2 with Giga bit Network Module AXXSW1GB installed in it , but now Network Module is is malfunctioning, I want to replace it now, but it has End of Life, means no more production, is there any replacement by intel.
Hi Guys,
I own two Intel Grizzly Pass platform and i'm a bit confused about cabling. Both were bought as used and shipped with extra parts.
[System1] - R2224GL4GCSAS
I have this set up as per Hardware User Guide for Intel® RAID Expander RES2CV240 and RES2CV360
A, B, C, D, E ,F on SAS Expander are connected to backplane where H, I goes to Integrated RAID RMS25CB080
Is that correct configuration?
Is Integrated RAID RMS25PB080 supported as extra RAID controller to add more throughput to slots 16-23 if directly connected to them?
[System2] - R2312GL4GCSAS
In the service manual on page 18 it says to connect Integrated RAID RMS25CB080 to SAS Expander and then to backplane.
I have a spare Integrated RAID RMS25PB080 but in the current configuration it is not connected. Current configuration is:
SCU_0(no key installed) is connected to miniSAS_0 on backplane and Integrated RAID RMS25CB080 is connected to miniSAS_1 and miniSAS_2
From my understanding first four slots in backplane will be SAS 3Gb/s and the other eight connected to Intergrated RAID will be 6Gb/s?
What if i connect miniSAS_0 to Integrated RAID RMS25PB080? Do i have to buy SAS Expander if i want to fully utilise all slots inSystem2?
Regards
Hi,
We're getting errors when a setting up SSD Cache on single and multiple VDs with the RMS3CC080 Raid cards (we have tried 2 new raid cards both have the below problems).
The problem only seems to exist with the latest firmware (v24.16.0-0082), previous FW: (24.15.0-0023) seems to works fine.
You can create the SSD Cache VD fine, it's when you go to 'enable' the SSD Cache on one or more VDs when it either simply wont enable OR you get the below error:
When you upgrade to the latest FW v24.16 with SSD config already assigned to multiple VDs, then it seems to work OK, but when you clear configuration and try to start from scratch, the errors start again.
Can I ask Intel is this a problem Intel is aware of and will it be fixed in the next FW release?
For now we're running with the previous FW rev. 24.15.0-0023, but the customer may upgrade later without our knowledge...
Thanks for your help.
Rob.
I'm looking to make a Virtualization Home Lab. I want to eventually run the router as a VM along with a Web- + Mailserver.
I learned I need SR-IOv functionality. Now I wonder if this mobo above has SR-IOv (Single Root IO Virtualization) support?
What other things do I have to be aware of beyond the mobo supporting SR-IOv?
Ihave installed software stack on centos 7 for intel xeon phi 7120p , everything are succed , micctrl -s gives output mic0 ready ( online ) , my question is how to run this coreprocessor with the other 2 intel xeon e5-2603 v3 in the host server , so that ican manage phi as main processor .??
I am in the process of setting up a ThinkServer TD350 with a Intel Xeon E52650V3 2.3Ghz Processor, and a TD-350/E5-2600 Motherboard, 16GB of 2R x 4 PC4 1700R RDIMM RAM.
The server is running Windows Server 2016. BIOS and TDM (Thinkserver Deployment Manager) were both updated prior to installing the O/S and before attempting the chipset update.
From the device manager it shows "Intel(R) C610 series/X99 chipset SMBus Controller 8D22 Version 10.1.2.19 Dated 1/26/2016"
According to Lenovo's suggested downloads I am to install the Intel DD_INTEL_CHIPSET_10.1.2.77_Public_Win_x86x64.
Installing this update caused the server to go Blue Screen with the error code: WHEA UNCORRECTABLE ERROR, for which the server gathered information and rebooted.
Lenovo suggested I download and run a (Microsoft Partnered) utility named Winthrust by Avangate/Solvusoft to clean up the registry, unused dll files etc. The program was to have 25 free uses. When I tried to apply the removal of said problems, it popped up a message that the free trial was expired and I had to buy the product, which I did for $30.00. I then found out from a Malwarebytes scan that this "utility" has a red flag warning that it is malware/spyware. I promptly removed the product. In a search I found numerous mentions that the Winthrust software utility and Avangate/Solvusoft was marketing a spyware product.
I have also run the Intel driver update utility. The Intel utility displayed that there was a suspended driver installation and that it should be removed. I allowed the Intel driver utility to clean things up. The Intel utility then indicated that there were NO driver updates needed.
I again tried to install the chipset update and the system went blue screen again with the same error. After the system rebooted I again ran the Intel driver update utility in which it again indicated that there was a suspended driver installation.
I now believe that the employees at Lenovo who have answered my questions about this problem do not have the correct information. Advising customers to download known malware/spyware for use indicates that Lenovo support may not have their customer's best interests in mind.
First off, I apologize for being a noob. I'm still trying to figure out what questions to ask to get the info I need.
I'm building an Intel Server with the S2600CW2R board, Intel RS3DC080 Raid, and 4- 4tb sas drives in RAID5.
I'm trying to UEFI boot and Install Windows Server 2016. And I've run into some problems and questions.
1. The server, even when set into UEFI in the BIOS, just doesn't want to UEFI boot from the Server Install DVD. I'm using a standard dvd-rom connected via SATA to the motherboard set to AHCI. I've tried RAID mode as well with similar results. Even what I manually select the boot device from the boot menu, UEFI isn't an option. I'm probably missing some step, configuration, or some nerd knob somewhere that needs turning. I'm sure someone has made this work at some point, can y'all clue me in on what configuration I need to be looking at? Or at least point me in the right direction please.
2. Backup & Restore - This is more a Windows question but it falls in line with the first one. In Windows Server 2016, does the backup and restore support UEFI, GPT, and large 4TB - 36TB RAID arrays? I've faced issues with 2008 & 2012 with disk/volume size limitations but haven't been working with 2016 enough to know what limitations are still in place. I've seen issues with Windows 10, UEFI, GPT, and Image Restorations failing. I'm curious with Server 2016 is plagued with the same problems and how y'all are dealing with them.
Thank you all for your time and assistance.
Cecil W.
Hello
I apologize in advance for the presentation of the text, write in Russian and translate in the browser.
Asking for help from professionals. Platform "R1304SPOSHBN", fully assembled, all components are in their places, the processor is "XEON E3-1230 v6 ", RAM 2*16GB Kingston KVR24E17D8/16MA
The problem is that when the system starts the testing begins, the fan speed maximum rpm is reduced to minimum and testing apparently ends, then should start to boot the system (?), however on the screen nothing appears either during testing or after. However, after the fall of the fan speed, about 30 seconds later the server rebooted, then again and again. The screen is totally unresponsive. Apparently the problem with the built-in graphics card, but connecting the external new and serviceable graphics card has not produced results. BIOS reset.
In this case, can advise? How to diagnose the problem? The server is brand new, probably made a mistake somewhere with the connection of the components, but did everything according to instructions.
Help Board!
I am trying to install Windows 7 Pro x64 to Intel dbs1200splr.
I need to enter username and PC name during installing but i can't. Keyboard and mouse are not working in any USB ports(2.0 or 3.0). There is no PS/2 port to try another keyboard.
In BIOS or WinPE keyboard and mouse are normally works, no troubles.
So, How i can to install Win7?
Hi All,
Does anybody have any information about this error?
We have 3x Brand new S2600WTTR Intel Servers and all 3 are producing this error every few weeks:
SPS FW Health reports SPS Health event type FW status. PECI over DMI interface error. Recovery via CPU Host reset or platform reset. DMI timeout of PECI request.
This is causing a hard reset on each of the systems.
If anyone has any more info on what would be causing this it would be greatly appreciated
Hey there,
I cant quite seem to figure out why my fans seem to hate me. The PCI domain fan constantly speeds at 3,500 RPM regardless of what i change and I believe it should be spinning at around 1000-1400 compared to what other people have reported but mine refuses to go down to that level. I have quite mode enabled so the CPU domain fans are spinning very slowly which is correct.
The event log shows no obviously errors and all the sensors are green, only a few are not available. The bios, me, bmc, sdr are all updated with the latest versions as well.
Is someone elses info where it shows 1218 RPM which i would love to have.
[code]
001a | Full | Fan | 30 | System Fan 1 | OK | 1218.00 RPM
001b | Full | Fan | 31 | System Fan 2 | Init | 0.00 RPM
[/code]
Mine however is like this...
[code]
➜ ~ ipmitool sensor
Pwr Unit Status | 0x0 | discrete | 0x0000| na | na | na | na | na | na
IPMI Watchdog | 0x0 | discrete | 0x0000| na | na | na | na | na | na
Physical Scrty | 0x0 | discrete | 0x0000| na | na | na | na | na | na
FP NMI Diag Int | 0x0 | discrete | 0x0000| na | na | na | na | na | na
SMI Timeout | 0x0 | discrete | 0x0000| na | na | na | na | na | na
System Event Log | 0x0 | discrete | 0x0000| na | na | na | na | na | na
System Event | 0x0 | discrete | 0x0000| na | na | na | na | na | na
Button | 0x0 | discrete | 0x0000| na | na | na | na | na | na
VR Watchdog | 0x0 | discrete | 0x0000| na | na | na | na | na | na
SSB Therm Trip | 0x0 | discrete | 0x0000| na | na | na | na | na | na
BMC FW Health | 0x0 | discrete | 0x0000| na | na | na | na | na | na
System Airflow | 70.000 | CFM | ok | na | na | na | na | na | na
BB EDGE Temp | 25.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na
Front Panel Temp | 24.000 | degrees C | ok | na | 0.000 | 5.000 | 50.000 | 55.000 | na
SSB Temp | 43.000 | degrees C | ok | na | 0.000 | 5.000 | 98.000 | 103.000 | na
BB BMC Temp | 36.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na
BB P2 VR Temp | 34.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na
BB MEM VR Temp | 33.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na
HSBP 1 Temp | 25.000 | degrees C | ok | na | 0.000 | 5.000 | 110.000 | 115.000 | na
LAN NIC Temp | 48.000 | degrees C | ok | na | 0.000 | 5.000 | 115.000 | 120.000 | na
System Fan 1 | 3500.000 | RPM | ok | na | 392.000 | 462.000 | na | na | na
System Fan 2 | na | RPM | na | na | 400.000 | 460.000 | na | na | na
HSC1 Status | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P1 Status | 0x0 | discrete | 0x8000| na | na | na | na | na | na
P2 Status | 0x0 | discrete | 0x8000| na | na | na | na | na | na
P1 Therm Margin | -59.000 | degrees C | ok | na | na | na | na | na | na
P2 Therm Margin | -60.000 | degrees C | ok | na | na | na | na | na | na
P1 Therm Ctrl % | 0.000 | percent | ok | na | na | na | 30.000 | 50.000 | na
P2 Therm Ctrl % | 0.000 | percent | ok | na | na | na | 30.000 | 50.000 | na
P1 ERR2 | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P2 ERR2 | 0x0 | discrete | 0x0000| na | na | na | na | na | na
CATERR | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P1 MSID Mismatch | 0x0 | discrete | 0x0000| na | na | na | na | na | na
CPU Missing | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P1 DTS Therm Mgn | -59.000 | degrees C | ok | na | na | na | na | na | na
P2 DTS Therm Mgn | -60.000 | degrees C | ok | na | na | na | na | na | na
P2 MSID Mismatch | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P1 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P2 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P1 MEM01 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P1 MEM23 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P2 MEM01 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na
P2 MEM23 VRD Hot | 0x0 | discrete | 0x0000| na | na | na | na | na | na
DIMM Thrm Mrgn 1 | -33.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na
DIMM Thrm Mrgn 2 | -41.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na
DIMM Thrm Mrgn 3 | -43.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na
DIMM Thrm Mrgn 4 | -42.000 | degrees C | ok | na | na | na | 5.000 | 10.000 | na
Mem P1 Thrm Trip | 0x0 | discrete | 0x0000| na | na | na | na | na | na
Mem P2 Thrm Trip | 0x0 | discrete | 0x0000| na | na | na | na | na | na
Agg Thrm Mgn 1 | -30.000 | degrees C | ok | na | na | na | 0.000 | 0.000 | na
Agg Thrm Mgn 2 | -26.000 | degrees C | ok | na | na | na | 0.000 | 0.000 | na
BB +12.0V | 11.883 | Volts | ok | na | 10.635 | 10.947 | 13.027 | 13.391 | na
BB +5.0V | 5.046 | Volts | ok | na | 4.460 | 4.590 | 5.415 | 5.566 | na
BB +3.3V | 3.354 | Volts | ok | na | 2.953 | 3.039 | 3.554 | 3.654 | na
BB +5.0V STBY | 4.937 | Volts | ok | na | 4.460 | 4.590 | 5.415 | 5.566 | na
BB +3.3V AUX | 3.296 | Volts | ok | na | 2.953 | 3.039 | 3.554 | 3.654 | na
BB +1.05V P1Vccp | 1.146 | Volts | ok | na | 0.546 | 0.564 | 1.464 | 1.506 | na
BB +1.05V P2Vccp | 0.804 | Volts | ok | na | 0.546 | 0.564 | 1.464 | 1.506 | na
BB +1.5 P1DDR AB | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na
BB +1.5 P1DDR CD | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na
BB +1.5 P2DDR AB | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na
BB +1.5 P2DDR CD | na | | na | na | 1.339 | 1.387 | 1.611 | 1.659 | na
BB +1.8V AUX | 1.785 | Volts | ok | na | 1.644 | 1.702 | 1.902 | 1.960 | na
BB +1.1V STBY | 1.071 | Volts | ok | na | 0.938 | 0.964 | 1.240 | 1.276 | na
BB VBAT | 3.158 | Volts | ok | na | 2.211 | 2.544 | na | na | na
BB +1.35 P1LV AB | 1.336 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na
BB +1.35 P1LV CD | 1.348 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na
BB +1.35 P2LV AB | 1.354 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na
BB +1.35 P2LV CD | 1.348 | Volts | ok | na | 1.201 | 1.244 | 1.445 | 1.488 | na
HDD 0 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
HDD 1 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
HDD 2 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
HDD 3 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
HDD 4 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
HDD 5 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
HDD 6 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
HDD 7 Status | 0x0 | discrete | 0x0100| na | na | na | na | na | na
NM Capabilities | 0x7f | discrete | 0x0300| na | na | na | na | na | na
P1 MTT | 0.000 | percent | ok | 0.000 | 0.000 | 0.000 | 0.000 | 0.000 | 0.000
P2 MTT | 0.000 | percent | ok | 0.000 | 0.000 | 0.000 | 0.000 | 0.000 | 0.000
[/code]
Is there anywhere that I can access drawings for a server chassis, server board, and compute module?
Thank,
Jordan Parker
I have "correctable ecc asserted" warning in the bmc of my server. This event probably lead to the server status light turned amber and blink. I wonder is this event mean only one bit error occurred in the dimm or the number of error occurred in that dimm exceeded the threshold? If it is the first case, I think it is ok, and won't lead to any server health problem. I hope someone can help me with this!
my platform bases on e5-2697v2 and w2600cr .
couples of days ago it cannot be powered on , beeps 1-5-4-2 , which means dc failure .
this goes on with or without board battery .
i think my power cases are running normally , so the mainboard is to be replaced .
but thing is that w2600cr is discontinued 2years ago , so that is the question .
please help !!!
Hello,
I am configuring an R1304SPOSHBNR 1U Rackmount Server.
I would like to know if the e3-1245v6 CPU is compatible with this.
If it is not compatible I would use an e3-1240v6 but this CPU has not got integrated graphics, would I need to have a graphics card in the expansion slot to get VGA video out?