Hello,
I have Blade Servers on MFSYS25, and I need at least activate Advanced Management Pack (MFSADVMGMT) for SysLog feature.
In a good case, I need the same for Shared LUN (MFSLUNKEY).
Our distributor said that he can't help us in this matter.
What should I do in this case?
Thank you.
Mainboard: SC2600CP2R mainboard with 2 Xeon CPU's and 128 GB Ram, latest firmware, works perfekt.
RaidControler: RS3WC080 with 4x1TB Seagate Intel-certificated SAS Drives, latest firmware.
i am able to create a virtual device (raid-5 array with state optimal, 3 x 1 TB + 1 hotspare), but can't declare as boot-device, boot device is always "none".
This happens in boot-mode legacy (configuration with CTRL-R) and in boot.mode UEFI (configuration over PCI-Configuration -> UEFI Option Rom Control -> Storage Controler)
Installation of VMWARE 6.5 or Windows Server 2016 stops with "no boot device found"
I spend a lot of time, but can't find any error.
I would be very happy if somebody can help me
Norbert
I'm having trouble booting a S1200V3RP server board with a Core i3-4130T installed.
It doesn't sound any beep codes, and generates video as far as displaying the following:
Version 2.14.1219.Copyright(c) American Megatrends, Inc
Installed BIOS: S1200RP.86B.03.01.0002
Platform ID: S1200RPS
After a few seconds, the status LED on the motherboard begins flashing orange. The diagnostic LEDs show a code of 00101011 which doesn't appear to be documented (it was mentioned in another thread here, but never resolved).
CPU is a Core i3-4130T which appears to be fully supported with this board and BIOS. Both board and CPU are new.
I have tried three different RAM modules that should all be supported, and have installed in slot A1 for troubleshooting.
Removing the RAM generates a three-beep error code as expected; likewise, removing the CPU generates 1-5-2-1.
Can anyone provide further troubleshooting advice? Thank you in advance.
Dan
Hello Everybody,
there is anyone knows if we can use the liquid cooling system on Intel Server Board S7200AP and which reference, from which manufacturer?
Thank you in Advance
Hi,
we have several new Servers with the S2600WTTR Mainboard (System BIOS - R01.01.0021 and R01.01.0022).
When we connect a USB 3.0 Disk (WD Elements 2TB), the server beeps and restarts.
Beep Code: 1-5-4-2
Associated Sensor: Power fault
Reason for Beep: DC power unexpectedly lost (power good dropout) -Power unit sensors report power unit failure offset...
In the BMC Server Health log i have this entries:
| 8 | 07/21/2017 16:11:06 | Pwr Unit Status | Power Unit | reports the power unit has suffered a failure - On-board 5V and 3V3 Power failure, - Deasserted |
| 227 | 07/21/2017 16:11:05 | Pwr Unit Status | Power Unit | reports the power unit is powered off or being powered down - Deasserted |
| 226 | 07/21/2017 16:11:00 | Pwr Unit Status | Power Unit | reports the power unit is powered off or being powered down - Asserted |
Update:
I have this problem on Servers with Vmware installed / also on Systems with Windows - Do i need to check some Bios Settings ?
If the Server stands on BIOS Screen and you connect the USB Disk, also a power fault occure and the server restarts...
Any ideas ? any help is appreciated! Thanks in advance!
服务器重启以后找不到系统盘，设置了启动项后保存可以进系统，再次重启以后启动项就会自动变更，然后就找不到系统盘
MB s2600wtt does not see the RAID controller RMS3CC080 at boot time. And you can not see how to get into the BIOS of the controller.
So I'm building a deep learning machine with 1 Xeon e5-2620v4 and 2 gtx 1080ti on top of an Intel S2600CW2R server board..
I bought it at a local store, and ask them to assemble my system. When it arrived, the system won't even POST or giving me any output on the display, just blank(tried to plug the cable to the GPU card and the onboard connector, results are the same). After doing some research, I found that the local store misplaced the GPU on the wrong PCIe slot. I fix this, get the system POST, and the display works(plugged the display cable to the onboard display connector) and install ubuntu 16.04 server.
After that, I tried to "lspci | grep NVIDIA" and the output gave me nothing. So I thought it must be the drivers that need to be installed. I installed the "nvidia-381" package from "ppa:graphics-drivers/ppa", reboot the system, tried to "lspci | grep NVIDIA" again, still nothing. Then I tried " nvidia-smi" but the output says ""NVIDIA-SMI has failed because it couldn't communicate with the NVIDIA driver. Make sure that the latest NVIDIA driver is installed and running"
So I jump into conclusion that somehow, the motherboard cannot detect any of the plugged GPU card. How can I resolve this issue ? Have anybody encountered the same issue ? If it's a hardware failure, i just want to be sure..
Note:
I have built two of these now and have them side by side and they both seem to act the same way at idle. The CPU is quite cool and it doesn't matter if the cover is on or off. There are only SSDs being used as well, so no extra heat being produced by spinners. No thermal events are logged by IASC or Windows during these events and there don't seem to be any issues at all. My assumption is that this must just be typical behavior for this unit. Can anyone confirm this?
Hi,
We're getting errors when a setting up SSD Cache on single and multiple VDs with the RMS3CC080 Raid cards (we have tried 2 new raid cards both have the below problems).
The problem only seems to exist with the latest firmware (v24.16.0-0082), previous FW: (24.15.0-0023) seems to works fine.
You can create the SSD Cache VD fine, it's when you go to 'enable' the SSD Cache on one or more VDs when it either simply wont enable OR you get the below error:
When you upgrade to the latest FW v24.16 with SSD config already assigned to multiple VDs, then it seems to work OK, but when you clear configuration and try to start from scratch, the errors start again.
Can I ask Intel is this a problem Intel is aware of and will it be fixed in the next FW release?
For now we're running with the previous FW rev. 24.15.0-0023, but the customer may upgrade later without our knowledge...
Thanks for your help.
Rob.
STOP 0x00000124 BSoD occured in the following environment and at the following timing.
The environment
-S1200SPLR (FW:03.01.0021)
-Windows 2016 standard (clean installed)
-Pentium G4560
-SanMax SMD4-E16G28H-21P-D DDR4-2133 U-DIMM ECC 8GBx2
-AVAGO MegaRAID 9265-8i (PCIe x8)
-Intel Expander RES2SV240 (PCIe x4)
-Broadcom BCM957810A1006G 10GbE (PCIe x8)
-Samsung SSD 840 EVO (SATA)
When BSoD occurs
-Run Windows Update
-Install Chipset Driver
I tried the following, but I did not improve it.
-Remove all PCIe cards
-Run Memtest86 >> no error
-clean install OS
-Replace the keyboard and mouse
Thank you for your assistance.
Hello Everybody,
there is anyone knows if we can use the liquid cooling system on Intel Server Board S7200AP and which reference, from which manufacturer?
Thank you in Advance
I have Intel Server Board S2600CP in Intel Server Chassis P4000S with 5 fan coolers. Server two year worked correctly. But, one weak ago, 5 fan coolers started working too fast and too load. Installed one processor - Xeon E5-2603, and her temperature about 30 C.
I upgrade BIOS on last firmware: BIOS - 02.06.0005, ME - 02.01.07.328, BMC - 01.27.9958, FRUSDR - 1.11. During upgrade i set Chassis serial number, Chassis part number, System serial number and System part number correctly.
In BIOS settings set parameters: Set Throttling Mode - [Auto], Altitude -[300m or less], Set Fan Profile - [Acoustic]. For tests i set various parameters in BIOS, but 5 fan coolers worked very fast and very load all time.
Ask me please, how to diagnostic and correctly configure my server.
Thanks.
Good After!
I need the help of the Technical Department, because I have a H2312XXLR3 barebone with 2 Compute Module HNS2600BPQ, and they do not power either one.
The Buttons Power and ID, don't respond.
I don't understand the origin of this problem.
Kind Regards
Hi everyone,
I am having an issue with a Dell R720 server.
I see tons of drivers which appears with: No drivers are installed (picture below)
I have the same on both Windows 2016 and windows 2012 R2
I've installed all I could find from Dell's website, updated all: iDrac/Lifecycle/Bios/Chipset/Drivers
Has anyone encountered this? Anyone who could guide me in the right direction?
Hello!
I have Intel MFSYS25 in this configuration:
6 modules of computer modules MFS5520VI.
4 modules DPS-1000DB A 1050W Power Supply, all power supply modules are connected to the power network.
At the moment, only two blades of six work.
When trying to start one or more, the chassis writes this:
What happened?And why can not I run more than two blades?
Hi every one!
Please help me this case, I use a Intel Modular Server,
When i configure Switch on the Modular server, i could not save configure.
after switch restart, the switch does not save my configre and go to factory default
How can i save the switch
thanks
Mainboard: SC2600CP2R mainboard with 2 Xeon CPU's and 128 GB Ram, latest firmware, works perfekt.
RaidControler: RS3WC080 with 4x1TB Seagate Intel-certificated SAS Drives, latest firmware.
i am able to create a virtual device (raid-5 array with state optimal, 3 x 1 TB + 1 hotspare), but can't declare as boot-device, boot device is always "none".
This happens in boot-mode legacy (configuration with CTRL-R) and in boot.mode UEFI (configuration over PCI-Configuration -> UEFI Option Rom Control -> Storage Controler)
Installation of VMWARE 6.5 or Windows Server 2016 stops with "no boot device found"
I spend a lot of time, but can't find any error.
I would be very happy if somebody can help me
Norbert
Hi,
I have difficulties with EFI Boot.
Long story short:
Having BIOS revision R0064 I'm trying to boot OS V 10.11 El Capitan.
The process is trail/error, so I need an easy way to change the BIOS Boot mode between MBR/EFI.
It is because I'm not sure I have proper disk for EFI boot, although I've got an OS X 10.11 installed on the machine and it doesn't boot in MBR mode, but if I set EFI Optimized Boot and try to boot my installation I don't have an success. The error code is 0xD6 - Trying boot selection.
The worst thing is I don't have an access to the BIOS Set Up at all so, I have to recover or update the BIOS to get the system working.
Any ideas?
Thanks.
I'm having trouble booting a S1200V3RP server board with a Core i3-4130T installed.
It doesn't sound any beep codes, and generates video as far as displaying the following:
Version 2.14.1219.Copyright(c) American Megatrends, Inc
Installed BIOS: S1200RP.86B.03.01.0002
Platform ID: S1200RPS
After a few seconds, the status LED on the motherboard begins flashing orange. The diagnostic LEDs show a code of 00101011 which doesn't appear to be documented (it was mentioned in another thread here, but never resolved).
CPU is a Core i3-4130T which appears to be fully supported with this board and BIOS. Both board and CPU are new.
I have tried three different RAM modules that should all be supported, and have installed in slot A1 for troubleshooting.
Removing the RAM generates a three-beep error code as expected; likewise, removing the CPU generates 1-5-2-1.
Can anyone provide further troubleshooting advice? Thank you in advance.
Dan