Clik here to view.
S2600CP2 - On losing PSU power, it won't post, except after a CMOS flash,...
S2600CP2 - On losing PSU power, it won't post, except after a CMOS flash, even on a clean shutdown from OS - Feature or known issues and how to change if its a feature? I have two S2600CP2 boards,...
View ArticleS2600CW2SR won't post, gives 1-5-4-4 beep code
As the title suggests, I cannot get this board to POST. I've tried with only one stick of RAM and the board out of the case I purchased for it, but no matter what I do I still get a 1-5-4-4 beep code....
View ArticleClik here to view.
s2600cp BMC Firmware Failure reported, fans at 100%
I have SuperMicro system (I think SS-AMZ1BA02) with s2600cp board installed. My fans are running at 100% all the time, and that's very annoying. I've tried a lot of different things to battle that, but...
View ArticleRed LED flashes on the baskets supermicro
Hi! I have the server Supermicro X8SI6-F / X8SIE (-F) / X8SIE-LN4 (F)Are the 3 disks in raid 5.Red LED flashes on the baskets, which drives 1 and 2 (0 - green).The Intel Matrix Storage Console shows...
View ArticleIs there a specification on the R2208WT2SR MTBF?
I would like to know the MTBF for the R2208WT2SR server. Thank you, Steve Wasilko
View ArticleClik here to view.
S5000VSA error code 19F
S5000VSA SASBios version: s5000.86B.15.00.101Built date: 11/09/2010 2 x Intel Xeon 5310 1.6Ghz I have error 19F:Processor and chipset stepping configuration is unsupported. By continuing to boot, you...
View ArticleSC5400LX - SROMBSAS18E - F/W is in Fault State
Hi, I have a SC5400LX Intel System with a SROMBSAS18E installed (AXXRAK18E Key). The raid card is connected to a 6-Drive Hot-Swap Expander Kit (AXX6DRV3GEXP) and a 4-Drive Hot-Swap Expander Kit...
View ArticleXeon Phi as part of RDP Session-Host
Hi,I am very interested in Intel’s new Xeon Phi Coprocessors. We are an education company and we are planning to change a large amount of student’s workplaces from FAT- to Thin-Clients.This will cause...
View ArticleClik here to view.
modular server - modules can't see storage but no errors
Today I rebooted my modular server.After booting up all modules tried to boot from pxe because no drives were present.In the managment console you can see all virtual discs correctly configured and...
View ArticleSome general debugging help needed, W2600CR
Hello friends, over the past few months I've been trying to get this new build to work but nothing seems to work and the lack of debug output doesn't help.But after purchasing an internal VGA to normal...
View ArticleS1600 Jackson Pass 4 - Static IP address keeps disappearing
Hi, I have an issue with a S1600JP4 motherboard where the static IP address keeps disappearing. All four ports can link up just fine but could only ping for a certain amount of time before the IP...
View ArticleS5000XALR status light blinking green power button dissabled
Hello I recently bought a S5000XALR motherboard and I have installed it into a 4u chassis with no special features, just an on/off and reset switch, 3 leds, and 2 usb ports. I have added 4 8gb FBDIMMS...
View ArticleS2600WTTR - Redundant PSUs fail when power is lost to UPS
We have a brand new S2600WTTR 2U rack mount server w/ 2 redundant PSUs. Each is connected to a 1500 UPS along w/ other equipment in the server rack (other Servers, Router Switches, NAS...) if power...
View ArticleW2600CR Debugging help needed.
Hello friends, over the past few months I've been trying to get this new build to work but nothing seems to work and the lack of debug output doesn't help.But after purchasing an internal VGA to normal...
View ArticleClik here to view.
s1200sps
I welcome!At me problem with s1200sps In case of installation of the Windows 7 64bit/server 2008 r2 - doesn't see usb the keypad and a mouse, I can't begin installation!I apologize if a question...
View ArticleNeed help installing windows server 2012 r2 (evaluation)
I'm trying to install win server 2012 evaluation on a box that I was given to use but I can't load the OS via cd or usb. I have changed the boot options in the BIOS to boot from cd/dvd but after i save...
View ArticleS2600CP motherboard + P3600 SSD?
I own a S2600CP board with 2x Xeon's on it. It has the newest BIOS package upgrade (BIOS : 02.06.0002 - ME : 02.01.07.328 - BMC : 01.25.9398 - FRUSDR : 1.11) Now I have gotten a good offer for an Intel...
View ArticleBooting from DC P3700 on older server
Hello,I have an Intel SR2612URR server with a S5520UR board and a passive riser (along with the latest BIOS and BMC). Installed are two Xeon E5504 and 16 GB of registered memory.I purchased a DC P3700...
View ArticleS2600GZ Build - not booting
Hello all - I bought an S2600GZ motherboard a few weeks ago, and while it has failed, I have reinstalled the replacement Intel sent to me. The board does power on, and I am able to get a solid green...
View ArticleClik here to view.
Looking for Deployment Assistant for S2600CP family.
Specifically S2600CP2J. Found this page but the link doesn't work: Page - http://www.intel.com/content/www/us/en/support/server-products/000006745.html, Link -...
View Article